0
What else can I help you with?
What are switch legs?
When the neutral wire goes to the switch
What is a trembler switch?
A trembler switch operates by vibrations. Vibrations cause the switch mechanism to complete or interrupt an electrical circuit. It can be used to trigger and alarm, turn on lights or many other devices. A simple trembler uses a metal can (soup can) with a small hole in the top and a weight suspended from a bare wire through the hole with a weight attached to the end of the wire (the hole must be large enough so the wire does not make contact with the can). The other end of the wire is connected to a battery (or other power source). The other pole of the battery is connected to the can. When vibrations cause the weight to move enough to cause the bare wire going through the hole in the top of the can to contact the can the circuit is completed.
How do you wire in a pull chain switch in a bathroom light fixture?
If you are adding the pull chain to an existing fixture then the pull chain switch should have two wires. Wire nut either one to the hot wire coming in and the other to the black wire of the fixture.
What part of a circuit is the wire cable or switch?
Wire is the transition material used to carry the electric current; the switch is the controller of that current.
When at a 2 pole light switch and the wire colors shown are black white and green which is the hot wire and which is the common?
the black wire is the hot wire
What caues the tail light in the tail-brake light to burn dim when the light switch is on?
The cause of the tail light burning dim when the light switch is on could be a short in the wire or an exposed portion of wire. This can sometimes cause the bulb to lack power because the power is drawn to another area.
What would cause a power wire to burn from the starter to the battery?
why would my starter wire burn, going from starter to battery
What would cause vw golf gti 1992 ignition coil live wire to burn out?
vw golf ignition coil wire to burn out y
I replaced the ignition switch in a 92 f-150 and it cranks up but doesnt cut back off. Even with the switch off my instrument lights are still on unless I unhook the battery. Did I do something wrong?
probably. that or you pinched a wire creating a hot all the time wire.
When too much current flows through a wire it can cause?
the wire will burn red hot or desinigrate instantly
What can cause the turn signals odometer etc to go dead besides a circuit breaker on a 2002 Harley Sportster?
check and see if you have cut or pinched the wire harness going into the switch housing on the throttle side... i pinched mine and lost brake, turn lights,,, still had tail lights in the turn signals but that is because i was using a brake/turn controller on the rear lights...
Will a loose kill switch wire on a out board motor cause bogging down?
A loose kill switch wire on your out board motor will cause the engine to lose power. As the kill switch loses contact the motor will begin to bog down or completely quit.
What would cause the coil wire to burn out at the coil end of the coil wire on my 93 Toyota Camry?
Toyota Camry coil wire can burn out from age or excessive use. The manufacturer recommends that you change the coil wire every 30,000 miles.
Why would the passenger side power door lock on a Lexus not operate?
The coil of the door lock is open-shorted,etc. or the 12VDC to the coil is missing-could be a pinched wire or the switch not working.
Is there an overdrive relay switch on a 1995 ford t-bird and if so where is it located your overdrive button on the stick doesn't work and niether does the dash indicator light thanks?
Take off the shifter and see if the wire to the OD switch is cut My 94 Tbird wire got caught and pinched between the shifter and broke it It is a very thin wire so I spliced in a new piece of wire to fix the problem
Can you by pass the AC pressure switch?
If it is a 2-wire switch- yes If it is a 3-wire switch- no
How do you wire a single pole light switch?
To wire a single pole light switch, first turn off the power to the circuit. Then, connect the black wire from the switch to the hot wire in the electrical box, and the white wire to the neutral wire. Finally, connect the ground wire to the green screw on the switch. Turn the power back on to test the switch.
