answersLogoWhite

0

Yes, you install a GFCI on a 2 wire circuit.

User Avatar

Wiki User

13y ago

What else can I help you with?

Continue Learning about Electrical Engineering

How do you wire a GFCI if there are 2 black wires?

You will have to run new electrical wire or a single ground wire back to the panel (though the former is highly recommended). A GFCI outlet will cut off the circuit if it senses voltage leaking to ground. If there is no ground wire, it will not function.


What size circuit breaker for GFCI circuit in a normal size bath?

Normally it is a 20 amp using AWG 12/2 gauge wire. But it really depends on what size wire is on that circuit. If it is white AWG 14 gauge then use a 15 amp breaker. If it is yellow AWG 12 gauge then use a 20 amp breaker.


May a GFCI receptacle be installed as a receptacle in an old installation where the 2-wire circuit has no equipment grounding conductor?

Actually, yes. The GFCI does not need any ground; it measures "leakage", i.e., an imbalance, regardless of whether there is "ground". The National Electrical Code permits installing a GFCI to replace a completely ungrounded receptacle. Others have said: No. The GFCI is designed to measure an unintended path to ground. Without a good ground reference this is not possible.


Is it safe to go from 12-3 wire to a 14-2 wire in the middle of a switch leg?

No. The wire size is dependent on the circuit protection. If the circuit uses a 20 amp breaker you need to run 12 AWG wire on all devices connected to that circuit.


What is the size of wire gauge door?

The power to the garage door opener should be supplied by AWG 12/2 wire on a 20 amp breaker protected by a GFCI. The wire going to the sensors on each side of the door can be door bell wire.

Related Questions

How can I safely install 2 GFCI outlets on the same circuit?

To safely install 2 GFCI outlets on the same circuit, you should connect the line wires from the circuit to the line terminals on the first GFCI outlet, then use additional wires to connect the load terminals of the first GFCI outlet to the line terminals of the second GFCI outlet. Make sure to follow the manufacturer's instructions and consult a licensed electrician if needed.


Can one use 1 circuit of a 3 wire plus ground 2 circuit cable as a GFI circuit with the other as a lighting circuit?

A GFCI can not be used on a three wire branch circuit. It has to be on a single two wire circuit.


How do you wire a GFCI outlet with only 2 wires?

To wire a GFCI outlet with only 2 wires, connect the black wire to the brass screw and the white wire to the silver screw on the GFCI outlet. Make sure to follow the manufacturer's instructions and turn off the power before starting the installation.


How can I safely install 2 GFCI outlets on the same circuit to ensure proper functionality and protection against electrical hazards?

To safely install 2 GFCI outlets on the same circuit, follow these steps: Turn off the power to the circuit at the breaker box. Remove the existing outlet and replace it with the first GFCI outlet. Connect the wires to the appropriate terminals on the GFCI outlet (line and load). Install the second GFCI outlet downstream from the first one, connecting the load terminals to the line terminals of the first outlet. Test both outlets to ensure they are working properly and providing protection against electrical hazards. Turn the power back on at the breaker box. By following these steps, you can ensure that both GFCI outlets are properly installed and provide the necessary protection against electrical hazards.


How can an outlet be properly grounded with only 2 wires?

An outlet can be properly grounded with only 2 wires by using a Ground Fault Circuit Interrupter (GFCI) outlet. The GFCI outlet can provide ground fault protection even without a separate grounding wire.


Is it possible to use a GFCI outlet in place of an older two-wire outlet?

Answer for USA, Canada and countries running a 60 Hz supply service.Your question is, "Is it possible?" And yes, it is. It would work just fine as a 2 wire outlet. It will even provide GFCI protection, contrary to what many people believe.However, it is a violation of code and highly ill advised to do so. Code requires that when replacing any 2 wire outlet that it be upgraded to a 3 wire circuit. I know hardware stores still sell 2 wire outlets but that is beside the point. The third wire, the ground wire, is there for your protection, or it should be installed. There is no way to properly install a 3 wire outlet, GFCI or not, on a 2 wire circuit.The national Electric Code allows the replacement of two wire receptacles with three wire GFCI outlets refer to NEC section 406.4 for more clarity on the subject.As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.Before you do any work yourself,on electrical circuits, equipment or appliances,always use a test meter to ensure the circuit is, in fact, de-energized.IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOBSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS.


GFCI outlet outside this line feeds your two bathrooms can you install gfci outlets in these 2 bathrooms?

Yes, you can install GFCI outlets in the two bathrooms fed by the line from the GFCI outlet outside. It is a good safety practice to have GFCI protection in bathrooms to help prevent electrical shocks. Make sure to follow proper installation procedures and consult a licensed electrician if needed.


How many ground fault circuit GFCI circuit breakers are there in the circuit breaker panel of the secondary distribution center?

2


How do you install a new circuit for an outdoor outlet?

You will need an electrician. Tim is probably right in that unless you are knowledgable, call an electrican. Saying that, if you are knowledgable, you must install a GFCI circuit outdoors. This can be tied into an existing circuit if that circuit has no more than 9 existing lights & plugs already connected. Use 12/2 with ground wiring.


How do you wire a GFCI if there are 2 black wires?

You will have to run new electrical wire or a single ground wire back to the panel (though the former is highly recommended). A GFCI outlet will cut off the circuit if it senses voltage leaking to ground. If there is no ground wire, it will not function.


How do you install a 2 wire 3 way switch in a circuit?

To install a 2 wire 3 way switch in a circuit, first turn off the power to the circuit. Then, connect the two wires from the switch to the two wires in the circuit. Make sure to follow the wiring diagram for the specific switch model. Finally, secure the switch in place and turn the power back on to test the switch.


How do you wire a 120 volt gfci into a 240 volt three wire?

You can't. The 120 volt GFCI is probably just a 2-wire (hot, neutral and ground) You would have to run a new 3-wire (2 hots, neutral and ground). The two hots are how you get the 240 volts (120+120=240). Also you must make sure the wire is gauged properly. #10 wire for 30 amps, #12 wire for 20 amps, etc.