0
What else can I help you with?
How do you calculate cable glands from cable?
cable gland sise 20s means
Could you Calculate cable size for 100 kw load?
To calculate the cable size for a 100 kW load, you would need to consider factors such as the voltage of the system, the type of cable insulation, the ambient temperature, and the installation method. The cable size is typically determined by the maximum current the cable will carry without overheating. Using the formula: Cable size (mm²) = (2 x L x I x R) / (√3 x V x cosΦ), where L is the cable length, I is the load current, R is the resistance of the cable, V is the voltage, and cosΦ is the power factor, you can calculate the appropriate cable size for the 100 kW load.
What would the cable size be for a 90 meter armoured cable with a 110 amp supply with a 330 amp start up?
To calculate voltage drop to size the wire, a voltage must be stated.
What is the cable size of 1600kVA transformer?
Cable size is determined by current. You did not provide the current, nor did you include the voltage so that we could calculate the current. Please restate the question, and include either the current or the voltage.
How do you calculate cable size from the 1500 mm length?
To calculate the cable size for a 1500 mm length, you need to consider factors such as the load current, voltage drop, and the type of insulation material. First, determine the current carrying capacity required based on the load. Then, use a voltage drop formula to ensure the drop is within acceptable limits, typically around 3-5% of the supply voltage. Consult cable sizing charts or standards that provide guidance based on these parameters to select the appropriate cable size.
What is the type and size of cable gland or 2 core cable?
To answer this question the size of the cable or the amperage of the load is needed to calculate the correct wire size and connectors to fit the cable.
How do you calculate cable glands from cable?
cable gland sise 20s means
What size of cable gland for in metric 24 pair 1.5 mm sq cable?
For a 24 pair 1.5 mm sq cable, you would typically use a metric M40 size cable gland. This size provides enough room for the cable to pass through while maintaining a secure seal to protect against dust and moisture.
What is a cable gland?
A cable gland is a connector which holds the end of a cable in place.
How calculate the cable size when give current?
The NEC has a table that shows what size cable to use with each amperage and where it can be used.
Could you Calculate cable size for 100 kw load?
To calculate the cable size for a 100 kW load, you would need to consider factors such as the voltage of the system, the type of cable insulation, the ambient temperature, and the installation method. The cable size is typically determined by the maximum current the cable will carry without overheating. Using the formula: Cable size (mm²) = (2 x L x I x R) / (√3 x V x cosΦ), where L is the cable length, I is the load current, R is the resistance of the cable, V is the voltage, and cosΦ is the power factor, you can calculate the appropriate cable size for the 100 kW load.
What is a gland in cable?
A gland in cable, commonly called a cable gland, is a mechanical device used to secure the end of a cable to an enclosure, panel, or equipment. It provides strain relief, sealing, and environmental protection for the cable, ensuring safe and reliable performance.
What size of wire use for 3kw motor 380volts 3phase?
How to calculate a cable size of 3kw motor
What cable size needed for 3KW geyser?
You need to know the amperage requirement of the pump and then you can calculate the wire size.
How do you calculate the cable size for a run of 30 meters?
to calculate the cable size of a run of 30 meters long you first will have to know the current of the appliance use the voltage drop formula V d = (mVxIxL)/1000 once the voltage drop is less than 2.5% of the nominal voltage, the cable should be upsize.
For 100kw which cable size is good and how to find out cable size?
100 kw is the power drawn by the load. to calculate the cable size you need to know the voltage. From that you can calculate the current. this decides the cable size. for example if the voltage is 400Volts then the current flowing in the circuit when the load is 100 KW will be 250 amps. (100,000/400). for 250 amps to flow with out causing excessive heating of the cable the cross sectional area of the copper cable should be 150 sq mm.for a round cross section the diameter will be roughly 15mm.
What would the cable size be for a 90 meter armoured cable with a 110 amp supply with a 330 amp start up?
To calculate voltage drop to size the wire, a voltage must be stated.
