answersLogoWhite

0

you should inject an external fault current from the line side of one of the connected feeders CTs and measure diff (or operating) current and Restraint current and investigate stability of circuit!

User Avatar

Wiki User

13y ago

What else can I help you with?

Continue Learning about Electrical Engineering

How can you calculate the copper bus bar according to the amp?

To obtain the amp of the copper bus bar, multiply the width of the bus bar by the thickness of the bus bar to obtain the current carrying capacity of the bus bar.


What are the types of bus bar arrangements?

Single bus is used in smaller, less important substations. A fault on the bus requires tripping of all lines into the bus. When higher redundancy is necessary, ring and breaker and 1/2 schemes are used. These are the three most common.


Difference between bus bar and bus duct?

Bus bars are actually simple conductor strips of copper using for connection between one system to another.for example transformer to panel. bus ducts are enclouser of that bus bar


What is double busbar arrangement?

Double bus bar is related to power control center (PCC). PCC is the main LT power distribution in any industrial establishment or large residential complex too. It basically an electrical panel with required number of incomer feeders and outgoing feeders. Power source like state power or captive power provide the incomers and outgoing feeders cater to the down stream power panels for further distribution( to MCC). Any PCC has one or more incomer and one or more outgoing feeder and bus isolators depending on the requirement. This PCC needs to have a bus bar to which the incomer gets connected and feeds the power to the bus and the outgoing feeders are connected to the bus bar to deliver the power down stream. This bus bar can be single bus bar system or double bus bar system. In a double bus bar system the two different power sources are connected to two different bus. Say one bus is for DG set power another bus is for SEB power. Both the buses can be charged simultaneously and can feed any outgoing feeders. The out going feeder have flexibility of getting the power either of the buses, but not simultaneously from both the buses. Double bus bar is more expensive compared to single bus bar system but more flexible, reliable.


Are neutrial and ground wires to be separated in electric main box?

Yes, if possible, connect the grounds to the ground bus bar and the neutrals to the other side on the neutral bus bar. This is just in case you ever install a sub panel. It is not a violation of the NEC code to connect them to the same bus bar but IMO it is unprofessional and can cause problems later on.

Related Questions

What is high pressure test for bus bar?

A high-pressure test for bus bars involves subjecting the bus bar to increased pressure levels to check for leaks or weaknesses in the material. This test helps ensure that the bus bar can withstand the pressure it will face during normal operation without failing, which is crucial for safety and reliability in electrical systems.


How can you calculate the copper bus bar according to the amp?

To obtain the amp of the copper bus bar, multiply the width of the bus bar by the thickness of the bus bar to obtain the current carrying capacity of the bus bar.


What is the bus bar size for 6000A?

5-6x150 Cu. BUS BAR PER PHASE


What are the types of bus bar arrangements?

Single bus is used in smaller, less important substations. A fault on the bus requires tripping of all lines into the bus. When higher redundancy is necessary, ring and breaker and 1/2 schemes are used. These are the three most common.


Bus Bar?

Its a switch


What does the term 'bus bar' refer to?

The term "bus bar" refers to a strip of bar of brass, aluminum, or copper. This strip of bar conducts electricity with a distribution and switch board.


How do you convert bus bar to amp?

Bus bar is a physical component that carries the current. AMP is unit of current. They can not be converted


Why the impedance of infinite bus bar is zero?

...because it is an infinite bus bar, meaning it can supply infinite current. By Ohm's law, since the voltage at the bus bar is fixed, to have infinite current, you must have a zero impedance.


Difference between bus bar and bus duct?

Bus bars are actually simple conductor strips of copper using for connection between one system to another.for example transformer to panel. bus ducts are enclouser of that bus bar


What are the conditions for Synchronization of three phase alternator and bus bar?

voltage of incoming machine should be same as that of bus bar voltage


Bus bar and bus duct sizing calculations?

busbar sizing & calculation


In beams what is a zero bar?

A zero bar is a bar in a truss that supports no load but is only there for the stability of the structure