We can convert a 3 phase ac motor into generator by changing phase sequence of the ac input cable of that motor
A simple Rotary phase converter is just a motor generator set. An electric motor running on the input voltage/current/phase/frequency. it drives a generator that supplies a different voltage/current/phase/frequency. So an electric motor and an electric generator connected together mechanically, either on the same shaft, or via gears, constitutes a Rotary phase converter. the above is incorrect, the motor/generator is the same motor, just one 3 phase motor is needed, it will run on T1 and T2, and put out L1, L2, and L3. You just need to know how to wire it up and what to do to get it to spin over on simple single phase 220, it will create three phase 220.
probably about 50 hp depending on how reliable the efficiency ratings of the various manufacturers are
To see if the motor is three phase or single phase look at the motor's nameplate. There it will tell you what the voltage needs to be and what system phase the motor needs to be connected to operate properly.
3 phase reverse relay can be utilized to control 480V motor 60HZ for controlling their speedspeed.
When you do a load test on a 3-phase induction motor you are checking the power factor, viz slip, and efficiency of the motor. You can test various loads with this test.
The winding design of the motor will not economically allow this to work. You would have to drive a 3 phase generator to supply it.
Terminology gets misapplied but a 3-phase converter produces a 3 phase supply from a single phase supply. The only proviso is that generator, converter and motor are all suitably rated and compatible.
Yes, but the motor's horsepower rating will not be reached.
"2 phase" and "3 phase" are descriptions of AC supplies, which no DC generator can imitate, regardless of its power rating.
You would reverse rotation on a 3 phase motor to get it to run backwards. Say I fill up a tank truck from a lake. I turn on my generator. I run the motor in one direction. Then I drive the tank truck and the motor to a different location. Then I turn on my generator. I attach the hose to the motor on tank truck. I throw the switch to make the motor run backwards. I aim the hose at the fire in your house. Aren't you glad that I can make my 3 phase motor run backwards?
230 v 6 amps is 1380 VA which equals about 1 kW, so a 3 kW motor implies it's a 3 phase motor. It would turn over on a single phase supply in whatever direction it was first spun in, but the performance would be poor and the motor or generator could get damaged.
use a rotor phaser or simply connect a 3 phase motor and check dirrection
A simple Rotary phase converter is just a motor generator set. An electric motor running on the input voltage/current/phase/frequency. it drives a generator that supplies a different voltage/current/phase/frequency. So an electric motor and an electric generator connected together mechanically, either on the same shaft, or via gears, constitutes a Rotary phase converter. the above is incorrect, the motor/generator is the same motor, just one 3 phase motor is needed, it will run on T1 and T2, and put out L1, L2, and L3. You just need to know how to wire it up and what to do to get it to spin over on simple single phase 220, it will create three phase 220.
A motor converts electrical energy into mechanical energy, so it can't be used for lights. But a 3-phase generator or alternator can be used to generate power for lighting. A 3-phase generator can light 3 light simultaneously, or it can be used to with a full wave rectifier (as in a car's electrical generator) to light one light, or several lights, or charge a battery
You should get a 3 phase generator that has 8-12 KW. If you had to you could use a 3 phase 5.5-6 kw but it may wear out faster because you are using 100% power. The 3 phase gen will allow you to select 480 volt which can be converted to 380 for the mixer. The rpm of the motor in irrelevant because the generator is the power source in this situation, once the gen powers the motor it will produce 1140 to power the mixer.
The motor will turn
an electric motor is a copper winding or 3 separate windings depending on the phase, the copper winding is the centralised inside of a iron magnet, this is also how a generator is made instead of putting a current on you turn the windings to receive a voltage .