0
What else can I help you with?
How many lights can you put on a dimmer?
As many as the watts or current the dimmer specs say it will control - less 10 percent
Why is a torch switch important in a circuit?
A switch in a circuit will quickly allow you to break the circuit, without changing the wiring. For example, a light switch. By turning a light switch off, you are breaking the circuit and, thus, turning the light off.
You have just replaced your ceiling light and when you turned the power back on the light stays on even when you turn off the switch?
Re open the switch junction box after turning the power back off. If you can locate the wire that bring the voltage to the box make sure that this wire goes to the top of the switch. If it is tied into more black wires this could be receptacle circuits that are on all of the time. If this is the case, from this group add a pigtail from this group to the top of the switch. from the bottom of the switch find the wire that is going to the light. It is probably in the group that is tied together. Once found terminate this wire to the bottom of the switch. Put the breaker back on and try the switch.
How many lights can you put on 12 gage wire?
The number of lights you can safely put on 12-gauge wire depends on the total wattage of the lights and the circuit's amperage capacity. A typical 12-gauge wire can handle up to 20 amps, which translates to about 2400 watts on a 120-volt circuit. If each light uses, for example, 60 watts, you could theoretically connect up to 40 lights, but it’s essential to consider the total load and local electrical codes to ensure safety and avoid overloading the circuit.
Where do you put a switch in a series circuit?
From the standpoint of basic functionality, you can put the switch anywhere. In a series circuit, there is only one path for current flow. If you open the switch, you interrupt that pathway and turn the circuit "off."There may be practical reasons to put the switch in one place or another, however. Sometimes it's put in a particular place in the circuit for manufacturing reasons. In other circuits, safety may dictate that you put the switch in a particular place: in a ground-referenced circuit for example, you may want to put the switch so that one side is at the ground point.
How can I put a light switch on a timer?
To put a light switch on a timer, you can install a timer switch in place of a regular light switch. This allows you to set specific times for the light to turn on and off automatically. Simply follow the instructions provided with the timer switch for proper installation and programming.
How can I put a timer on a light switch?
To put a timer on a light switch, you can install a timer switch that replaces your existing switch. This timer switch allows you to set specific times for the light to turn on and off automatically. Simply follow the instructions provided with the timer switch for installation and programming.
How can I put a ceiling fan and light on the same switch?
To put a ceiling fan and light on the same switch, you can use a dual-function switch that controls both the fan and light simultaneously. This type of switch allows you to operate both the fan and light with a single switch, simplifying the control of both fixtures.
Energy Efficient Light bulbs question about Watts?
The watts because if you put a bulb that is in to much higher wattage than the one that you are chagning then it can cause too many problems and you can have a big piwer outage in you home
The power of the light bulbs is measured in what?
The amount of power they consume is measured in watts. The amount of light they put out is measured in lumens.
How many lumens is equal to 5 watts?
There is no direct conversion . . . different types of lamp bulbs put out different amounts of light per watt.
How do you check switch on riding lawn mower?
Unhook wires from switch make sure you mark them so you can put them back on properly. Put a battery powered test light on terminals in and out of switch try switch if the light goes on and off when you move the switch then it is working and you have other problems.
Where is reversing light switch on Nissan primera?
hen you put it in reverse
How many watts in 30 amp?
There is no way to tell, you don't have enough information. Watts are what you get by multiplying the amps x the voltage. Simply put, Volts X Amps = Watts.
How do you make dome light come on when door opens?
Put the dome light switch on door located on the headliner to the side of the light
What are the example of filipinism?
please put off the light... meaning please switch off the light
How do you replace brake light switch on suzuki forenza?
To replace the brake light switch on a Suzuki Forenza, locate it on the pedal shaft, release the wires that connect it, twist and then take out the old brake light switch and put a new switch in its place. The job can be done by any handy owner.
