0
First, you must know: There is no 4 ohm amplifier. All audio amplifiers have an output impedance of smaller than 0.5 ohms. So you use impedance bridging. No problem to connect the 0.5 ohm output to your 4 ohm loudspeaker. Scroll down to related links and look at "Impedance bridging - Wikipedia".
Wiki User
∙ 15y ago
Add your answer:
Earn +20 pts
What is 6ohm in amps?
Ohms is a measurement of resistance between the amp and speakers. Most home audio is 8 ohm, if you run 4 or 6 ohm speakers you cut resistance down and get more power out of the amp. Say your stereo is 100X2 @ 8ohm, if you use 4 ohm speakers you should get 50% more power BUT the amp is working twice as hard and can burn up.
Which law states that it takes one volt to push one amp through 1 ohm of resistance?
Ohm's Law.
1000watt rms 2 ohm 15inch subwoofer what would be the best wattage amplifier to pair with this and would it have to be 2 ohm aswell?
is it duel 2 ohm or duel 4 ohm or just a singel 2 ohm sub??? you can run anything from a 1 ohm amp to a 2 ohm amp just depending if you want to add another sub later if your wanting to add 1 later get 1 big enough to run 2 subs so you wount be wasting your money on sumthing you dont need say 5 months from now
How much watts does a Yamaha ypa-720 amplifier have?
105 watts chann @ 8 ohm speakers
Do three 1m ohm resistors equal a 3m ohm resistor?
Only if you connect then in series. RSERIES = Summation1toN (RN) RPARALLEL = 1 / Summation1toN (1 / RN)
Can I connect two 2 ohm speakers to the front channels of my amp and then connect 2 4 ohm speakers to the rear channels of my 4 channel amp?
This depends on your amplifier's specifications. i would recommend looking in the amplifier's service manual to avoid disapointment or damage to your amplifier or speakers.
Can you hook up two 8 ohm svc subwoofers to a one channel amp?
If you connect two 8 ohm speakers to the average car amp, then yes, probably. Most car amps can handle a 4 ohm load, which is what it would be.
I have a 2 channel nitro amp 2000watts amp and it always gets hot after 10min. it's been hooked it up to several cars and it's the only amp that gives trouble every other amp works fine?
If it's running so hot you can't touch it, in most cases it will be due to either the way the speakers are hooked up or the impedence of the speakers. You can incresse the resistance to the amp to have it run cooler by connecting speakers in series or getting speakers with a higher ohm rating. The lower the resistance (2 ohm, 4 ohm, 8 ohm) the more current flows though the amp making it hotter. Remember if you hook multiple speakers in parallel it will cut the resistance in half. So if you connect speakers that are 4 ohm to the same channel you are running at 2 ohm. Check your amp's ratings.
Can you connect a 8 ohm speaker for a amp designed for a 4 ohm load?
You can, but the available power will only be about half of rated, and the frequency response will be slightly different. Better would be to connect two 8 ohm speakers in parallel, making an equivalent 4 ohm speaker.
What ohms am i running if i have two 4 ohm speakers hooked up to my amp vs two 2 ohm speakers?
Don't know how you have subs wired but should be 4 ohm load is what your amp will see.
Can you use a 6 ohm and a 16 ohm speakers with a 6 ohm amp?
No. Not and maintain good balance and dynamic range.
Will using a 2 ohm 1200 watt amplifier be ok to use with three 4 ohm speakers 12 and 2-10?
If you connect three 4 ohm speakers in parallel, the amplifier would see a load of about 1.3 ohms. This definitely could damage the amp if you drive it too loud.
Can 270 watt speakers damage a 125 watt amp?
Not unless the speakers are rated at a resistance (ohms) that is incompatible with the amp. Speakers don't generate power, the rating only tells you how much they can handle. So, speakers capable of up to 270 watts, can certainly handle 125 watts. However, if the amp is not 1-ohm stable and the speakers are 1-ohm, you could cause the amp to cut out and overheat depending on the protection mechanism of the amp.
Will 8 ohm sub woofers work with a 4 ohm amp?
if you put 2, 8 ohm speakers together on the same channel you will trick the amp into seeing a 4 ohm load, it is not advisable to run a 8 ohm coiled speaker on a 4 ohm amp unless you do the above. So if you want to run 2 8 ohm speakers from a 4 ohm amp this will work the best although the amp will need to be hefty as its worse to underpower a sub than overpower it! I have used a 8 ohm speaker myself on a car amp and had no problems but it was not a cheap entry level amp! some amps will take it, others will get hot and enter protection mode. Hope this helps!!!
What is 6ohm in amps?
Ohms is a measurement of resistance between the amp and speakers. Most home audio is 8 ohm, if you run 4 or 6 ohm speakers you cut resistance down and get more power out of the amp. Say your stereo is 100X2 @ 8ohm, if you use 4 ohm speakers you should get 50% more power BUT the amp is working twice as hard and can burn up.
How do you connect 2 6 ohm speakers to an 8 ohm amplifier?
You can, but its power output will be a bit higher than its 8 ohm rating.
What you need to connect two 8 ohm speakers to your HD TV?
everything
