answersLogoWhite

0

no ----------------------------------------------------------------------------------- Stepdown transformer. More expensive than buying the correct light fixture. Y-THINK-Y

User Avatar

Tierra Keeling

Lvl 10
2y ago

What else can I help you with?

Continue Learning about Electrical Engineering

Why use 277v light fixtures instead of 110v light fixtures?

277v light fixtures are more efficient to operate and less expensive to install than a 110v fixture of identical wattage. 277v light fixtures are typically installed when 480V 3 Phase primary electric service supplies a commercial or industrial facility. 277v lighting circuits are single phase circuits using one of the 480v primary phases (A,B & C) to Neutral. The higher voltage allows more fixtures per circuit using smaller conductors and longer runs typically required in warehouse lighting applications. ( Amps = Watts/Volts: 400W/277V Fixture = 1.4 Amps, 400W/110V fixture = 3.6 Amps) With 480V 3 Phase primary service, 110V Single Phase power is created using a Step-down transformer. The voltage transformation process consumes power (kWh) and the 277V fixture will consume less kWh than a 110V fixture if identical wattage, especially in fixtures with ballasts such as fluorescent or High Intensity Discharge (HID), like Sodium, Metal Halide or Mercury Vapor.


What is the difference in amps used by lighting wired 277v vs 208v?

Answer for USA, Canada and countries running a 60 Hz supply service.Assuming you are using the same fixture, and assuming the fixture can operate on either voltage, you will get fewer amps with 208v than with 277v. However, a fixture designed for 208v will probably burn up on 277v, and a fixture designed for 277v will probably not produce any light on 208v.The two fixtures in reality are quite different. The 277v fixture is using one leg and neutral of a 277/480v 3 phase 4 wire system and the 208v fixture is using 2 legs of a 120/208v 3 phase 4 wire system.In commercial and industrial installations the 277v fixture is most common.As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.Before you do any work yourself,on electrical circuits, equipment or appliances,always use a test meter to ensure the circuit is, in fact, de-energized.IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOBSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS.


In a three phase four wire wye system having 277V for lighting the three phase motors operate on what voltage?

480 Volt


Can a 240 volt electric fan be run on 277 volts?

No...that's too much voltage, and 277v is normally three-phase power.


Need help sizing a resistor to reduce voltage from 277V to 120v with a 200mw watt load at 120volts?

Start with the load of 0.2 watts. The power rule says that watts equals volts times amps, or amps equals watts divided by volts, so 0.2 watts at 120 volts means 0.00167 amps. Now, look at Kirchoff's current law, which implies that the current in a series circuit is the same at all points. This means that the current in the resistor is also 0.00167 amps. Now, look at Kirchoff's voltage law, which implies that the sum of the voltage drops in a series circuit adds up to the voltage source. This means that the voltage across the resistor is 157 volts. Last, look at Ohm's law, which says that resistance is voltage divided by current. 157 volts divided by 0.00167 amps is 94,200 ohms. The nearest standard 5% value to that is 91,000 Ohms. Before leaving, though, check the power in the resistor. It is 157 volts times 0.00167 amps, or 0.26 watts, so you need at least a half watt resistor.

Related Questions

Is there a way to install a 120V light on a 277V circuit?

No, it is not safe or recommended to install a 120V light on a 277V circuit. The voltage difference could damage the light fixture and pose a fire hazard. It is best to use a light fixture rated for the appropriate voltage.


How can you attach a 120 v Light Fixture to a 277 v system do I need a ballast so what kinda of ballast?

To attach a 120V light fixture to a 277V system, you will need a step-down transformer with a 277V primary and 120V secondary. This will allow you to safely power the light fixture at the correct voltage. You do not need a ballast in this case, as ballasts are typically used with fluorescent lights and not for altering voltage levels.


Can SJ 300V rated wire be used for 277v light?

No, SJ type wire is not rated for 277V application. This wire is typically designed for lower voltage applications such as 120V or 240V. It is important to use wire with the appropriate voltage rating to ensure safety and compliance with electrical codes and standards.


Can a 1H75 be used with 277V?

No, a 1H75 ballast is designed for 120V input voltage. You would need a ballast specifically rated for 277V to operate fixtures at that voltage safely and effectively. It is important to match the input voltage of the ballast with the fixture’s voltage requirements to avoid damage or safety hazards.


Why use 277v light fixtures instead of 110v light fixtures?

277v light fixtures are more efficient to operate and less expensive to install than a 110v fixture of identical wattage. 277v light fixtures are typically installed when 480V 3 Phase primary electric service supplies a commercial or industrial facility. 277v lighting circuits are single phase circuits using one of the 480v primary phases (A,B & C) to Neutral. The higher voltage allows more fixtures per circuit using smaller conductors and longer runs typically required in warehouse lighting applications. ( Amps = Watts/Volts: 400W/277V Fixture = 1.4 Amps, 400W/110V fixture = 3.6 Amps) With 480V 3 Phase primary service, 110V Single Phase power is created using a Step-down transformer. The voltage transformation process consumes power (kWh) and the 277V fixture will consume less kWh than a 110V fixture if identical wattage, especially in fixtures with ballasts such as fluorescent or High Intensity Discharge (HID), like Sodium, Metal Halide or Mercury Vapor.


What is low voltage transmission?

In the supply industry it refers to circuits of below 1000 volts. Common voltages used are 120v, 208v, 230v, 240v, 277v, 400v, 415v, 480v.


What safety features are required for a 277 volt light circuit?

Don't let anyone touch the live electrical parts. This voltage is significantly more dangerous than 120V. If you touch it it's likely to grab you and not let go. All components must be rated for the voltage in question. Switches must be rated for 277V, as well as lights, all boxes, junctions, and all electrical wiring must have insulation rated for 277V or above. The circuit breakers must be rated for this voltage, and they must be rated for the available fault current which could pass through the wiring of the circuit, based upon this new voltage. Because this circuit is more than 150V to ground, there are more strict rules on who may perform the work. Review the rules for your locality before cracking any covers. It's likely you should be a licensed electrician before tinkering with this stuff.


What is a tri tap ballast?

A tri-tap ballast is a type of fluorescent light ballast that is designed to accommodate three different input voltages (120V, 277V, and 347V). This flexibility allows the ballast to be compatible with various power sources, making it useful in different settings where voltage requirements may vary.


Will 277V work with a 120V ballast?

The impedence of the ballast is system voltage dependent to allow required current to pass through the light fixture. If system voltage changes, the current passing through the light fixture changes, therefore to get designed output from the fixture, the ballast has to be changed.


Will a bulb rated at 277V work in a fixture that is 240V?

Yes, it will just not be quite as bright as it would be on the higher voltage circuit. You will see very little difference in the luminance.


What is the voltage rating of a motor on a 3 phase 4 wire 277V lighting circuit?

If the motor is a three phase the most likely voltage the motor operates on will be 480 volts.


What is the difference in amps used by lighting wired 277v vs 208v?

Answer for USA, Canada and countries running a 60 Hz supply service.Assuming you are using the same fixture, and assuming the fixture can operate on either voltage, you will get fewer amps with 208v than with 277v. However, a fixture designed for 208v will probably burn up on 277v, and a fixture designed for 277v will probably not produce any light on 208v.The two fixtures in reality are quite different. The 277v fixture is using one leg and neutral of a 277/480v 3 phase 4 wire system and the 208v fixture is using 2 legs of a 120/208v 3 phase 4 wire system.In commercial and industrial installations the 277v fixture is most common.As always, if you are in doubt about what to do, the best advice anyone should give you is to call a licensed electrician to advise what work is needed.Before you do any work yourself,on electrical circuits, equipment or appliances,always use a test meter to ensure the circuit is, in fact, de-energized.IF YOU ARE NOT ALREADY SURE YOU CAN DO THIS JOBSAFELY AND COMPETENTLYREFER THIS WORK TO QUALIFIED PROFESSIONALS.