0
Let A,B,C are inputs and Y is the output.
A B C Y
0 0 0 0
0 0 1 1
0 1 0 1
0 1 1 1
1 0 0 1
1 0 1 1
1 1 0 1
1 1 1 1
Mind it that Y=A+B+C is a logical operation in our case i.e. OR operation. It's not an arithmetic operation (i.e. not a sum operation).
Wiki User
∙ 11y ago
Wiki User
∙ 14y agoCount up from 0 to 255 in binary and all the outputs are 0 until all the inputs are 1.
Add your answer:
Earn +20 pts
How many transistors are in an AND gate?
6
What is propagation delay in flip flops?
Propagation Delay In digital logic, every gate has got some finite amount of delay because of which the change in the output is not instantaneous to the change in the input. In simple terms, the times it takes for an input to appear at the output is called the propagation delay. In Figure 6, tPHL, describes the time it takes for an input to cause the output to change from logic-level-high to logic-level-low. Similarly, tPLH, refers to the delay associated when an input change causes the output to change from logic-level-low to logic-level-high. The overall delay is average of these two delays.
How do you calculate Peak load on the power supply given different appliances and their ratings?
The minimum and the maximum input DC power the powersupply can have. For exemple: Imput 100 - 125 V 6 A and 200 - 240 V 3A.
What is the pin configuration of IC CA3130?
The CA3130 op amp has the following pinouts: 1 Offset null 2 Inv. input 3 Non-inv. input 4 V- and case 5 Offset null 6 Output 7 V+ 8 Strobe Use the link below to review a data sheet where you'll find more information than you can possibly use.
Would using a 60 foot extension cord which is 6 gauge 3 wire cord on a 220 volt single phase welder present any problems?
It shouldn't. Check the nameplate for input amperage of the machine. Your #6 wire is good for 60 amps. If the nameplate amperage is below 60 amps then you are good to go.
What is the pin configuration of ic 74266?
this shows you everything you need about them Pin Number Description 1 A Input Gate 1 2 B Input Gate 1 3 Y Output Gate 1 4 A Input Gate 2 5 B Input Gate 2 6 Y Output Gate 2 7 Ground 8 Y Output Gate 3 9 B Input Gate 3 10 A Input Gate 3 11 Y Output Gate 4 12 B Input Gate 4 13 A Input Gate 4 14 Positive Supply
How many minimum NOR gates is required to implement NAND gate?
A 2 input NAND gate requires 4 NOR gates.A 3 input NAND gate requires 5 NOR gates.A 4 input NAND gate requires 6 NOR gates.etc.
How many two input NAND gates are required to implement a four input NAND gates?
NOR gate = not(A or B) = A nor BAND gate = A and BAND gate = not(not A or not B)AND gate = not(not(A or A) or not(B or B))AND gate = (A nor A) nor (B nor B)Therefore using 2 input NORs to make a 2 input AND you need three NORs. If you wanted something different (e.g. a 5 input AND) the above proof can be modified appropriately to get your answer.
What is the rule for this input - output table 6 in 4 out?
There are an infinite possible answer. Among the simpler ones is: Output = Input - 2
How IC 7402 can be connected to use NOR gate?
IC 7402 is different from the other type of IC like 7404,7408,7432 and 7400 when it is connected to have an output desired... if you noticed all i mentioned ic is connected from left to the right. input pin 1 and 2, output pin 3 input pin 4 and 5, output pin 6 input pin 13 and 12, output pin 11 input pin 10 and 9, output pin 8 while in nor gate, to have the desired output it must be connected from right to left... input pin 2 and 3, output pin 1 input pin 5 and 6, output pin 4 input pin 8 and 9, output pin 10 input pin 11 and 12, output pin 13
How many rows will appear in a truth table with 6 variables?
2^6 = 64
How to Design and draw a combinational circuit using AND-OR-NOT gates that accepts an input number of three bits. The output of the circuit is a 6 bit number that is the square of the input number?
first create truth table, inputs should be combination of 3 bits i.e 8 possible combination. the outputs are the square of each input. you need 6 bits for the outputs since the square of 7 is 49 which is binary notation 49 is (110001) hence 6 bits. same goes for the other inputs. when the table is complete. find the Boolean function that drives each bit, preferably by K-maps to minimize the logic. Then from the equations, simply draw the circuit by using the necessary logic gates. There will be 3 inputs and 6 outputs for the overall circuit. Very easy but tedious. have fun
What is the output of AND gate if sine wave is input?
I assume the sine wave input is pure AC, meaning this signal is positive, and negative, as would come from a transformer winding. To not damage the fragile input to the AND gate, you should have a limit resister, say 1K ohm to 10 K ohm. Then the output of the AND gate will be a very clean square wave. It will be in phase with the input sine wave. You can add a small capacitor from the AND gate input to tr ground. IMPROVEMENT: The best kind of gate to use for this circuit is called a "Schmitt Trigger", which will really clean up the signal. It is only available as inverting, 1, 4, or 6 per package. You can easily use an inverting NAND, and run it through 2 gates to get your phase back to what you want. So for what you are doing, use a 10K input, to a 100 pF cap to ground, going into one section of a 74HC14 (6 inverters in one package), and then go through another section, if you need to get back to 0 degree phase shift. With the 2 inverters in a row, you can have 2 phases available. Or, you can add another R-C delay between the 2 sections, and make the phase shift to whatever you need. 90 degrees, no problem. With 6 inverters, you can phase shift on and on, and make all kinds of poly phase outputs. MORE FUN: With the Schmitt gate, you only need an R and a C from the output back to the input, and you will make a very stable Square wave generator. With a single diode, you can make a "one-shot" circuit, for constant pulse width. You can even make a PWM circuit, by DC biasing the input.
What are the Eight Inner Gates in Naruto called?
1. gate of oppening 2. gate of rest 3. gate of life 4. gate of pain 5. gate of closing 6. gate of joy 7. gate of shock 8. gate of death
How many transistors are in an AND gate?
6
What is the output value if the input value is 6?
Anything you like - it depends on the function that relates the output to the input.
What is the ISBN of A Gate at the Stairs?
The ISBN of A Gate at the Stairs is 978-0-375-70846-6.
