> Predetermination of regulation.
> Predetermination of efficiency.
> Less power loss.
eddy current loss in the transformer core is reduced by
The temperature rise is not considered in OC & SC tests of transformers.. But in Sumpner's test, temp. rise is considered.. Hence is called "Heat-run test".. Also, the transformers draw only the power req. to supply core & Cu. losses of transformer..
synchronous impedance can be calculated by performing oc test and sc test. by oc test,since the armature current is zero Vt=Ef . in short circuit test ,entire emf is consumed in circulating the short circuit current Isc,through the synchronous impedance. Zs=Ef/Isc.= (open ckt. terminal voltage for a certain field current)/(short ckt. current at the same field current)
UPF(Unity Power Factor) is connected as the power factor is 1. Unlike OC where quantum dynamic rules apply in SC the time space gravitational lensing takes place which is why only LPF can be used.
The reverse breakdown voltage of the 1N4007 diode is 1000 volts.
During load test the readings/performance could be monitored during load variation from zero 100% and short circuit.
OC and SC tests are used for predetermining the efficiency and % voltage regulation. It is more efficient test for a transformer than sumpner's test for 2 reasons. 1. two identical transformers are readily not available 2. two separate power supplies are required for the sumpner's test, whereas OC and SC are simple and best
eddy current loss in the transformer core is reduced by
(this question cannot be answered)
(this question cannot be answered)
OC Polinativelamas OC Komati OC Reddy OC Brahmin OC Mahammadeeyulu OC Acharyulu OC Gujarathi OC Marwadies OC Sikhs OC Muslim OC Islam OC Telaga OC Kapu OC Thoti OC Karanam OC Velama OC Vysya OC Naidu OC Kamma OC Chowdary OC Raju OC Jain OC Gupta OC Agarwal OC Mudiliyar OC Adi Velama OC Christian OC Gajula Kapus OC Kshatriya
to determine the transformer characteristics...
In OC test , the equipments are connected in LV side since we need to get rated voltage . if it is cinnected in HV side the value of voltage will be less and current wil be more.Hence the ordinary instruments cannot measure this value of current
The density of nitrogen is 1,2504 g/L.The density of air is 1,2922 g/L.Both values are at 20 oC.
overclocked
OC-n / OC-xxx indicates Optical Carrier signals which are carried over a SONET (Synchronous Optical Network) fiber optical network. The numbers after OC indicate various levels or data rates in the SONET hierarchy. Hierarchy goes like OC-1, OC3, OC-12, OC-24, OC-48, OC-96, OC-192 and OC-768 OC-1 is a SONET line with transmission speeds of 51.84 Mbit/s. OC-192 has a speed of 9953.28 Mbit/s (almost 10Gbps, so also called SONET 10G). You can get more details in SONET literature. - Neeraj Sharma
OC-n / OC-xxx indicates Optical Carrier signals which are carried over a SONET (Synchronous Optical Network) fiber optical network. The numbers after OC indicate various levels or data rates in the SONET hierarchy. Hierarchy goes like OC-1, OC3, OC-12, OC-24, OC-48, OC-96, OC-192 and OC-768 OC-1 is a SONET line with transmission speeds of 51.84 Mbit/s. OC-192 has a speed of 9953.28 Mbit/s (almost 10Gbps, so also called SONET 10G). You can get more details in SONET literature. - Neeraj Sharma