Usually switches brought together in a central spot for convenience. There could be one or more supply feeder and load connections to each device connected to the bottom side of the switches. In the back of the box there will be all of the cable ground connected together and placed under the ground set screw.
Re open the switch junction box after turning the power back off. If you can locate the wire that bring the voltage to the box make sure that this wire goes to the top of the switch. If it is tied into more black wires this could be receptacle circuits that are on all of the time. If this is the case, from this group add a pigtail from this group to the top of the switch. from the bottom of the switch find the wire that is going to the light. It is probably in the group that is tied together. Once found terminate this wire to the bottom of the switch. Put the breaker back on and try the switch.
Run the power line to a light box in each room, then drop a switch leg from each light box. The power line should daisy-chain to each box, with a "tap" off for the lights of each room. If you do not have experience with lighting or switch logic, it would be much more safe for you to contract with a qualified electrician.
There are multiple ways to wire a switch. If power is fed into the switch box, a second light would be wired one way, if power is fed into the light box, the second light would be wired a different way. This seems like it would be a task better given to a qualified electrician or local handyman.
To wire a French light switch, first, ensure the power is turned off at the circuit breaker. Connect the live wire (usually brown) to one terminal of the switch and the wire going to the light fixture (also brown) to the other terminal. The neutral wire (typically blue) should be connected directly to the light fixture, without going through the switch. Finally, secure the switch in its box and restore power to test the installation.
The rating of the main switch is decided upon by the current incoming mains. The main switch can't be lower than the incoming. In order to upgrade the main switch, the breaker box will need a complete upgrade.
You can find information on a VGA switch box online at the Walmart website. Alternatively, you can also find info on VGA switch boxes from retailers such as Amazon.
go to pokecenter and find the switch box to go from PC to team
You can find an outdoor light switch box for your patio lighting installation at hardware stores, home improvement stores, or online retailers that specialize in electrical supplies. Look for weatherproof and durable options to ensure the switch box can withstand outdoor conditions.
The headlight relay switch on a 2008 Jeep Patriot is typically located in the engine compartment fuse box. To find it, open the hood and look for the fuse box near the battery. The relay is usually labeled on the cover of the fuse box, and you can refer to the owner's manual for specific details on its location and identification.
The 1991 Acura Integra fuel cutoff switch can be found in the fuse box. The fuse box is in the engine compartment. The cutoff switch location can be found on the inside cover of the fuse box.
A gang switch is an electrical box that contains two or more switches or outlets. Gang switches are very common in public facilities such as schools and hospitals. A two gang switch would be two switches operating different fixtures sharing the same electrical box.
On a 2006 Acura TL, the glove box switch is typically located on the underside of the glove compartment. To access it, open the glove box and look for a small switch or lever that controls the glove box light. If you're looking for the glove box latch or release mechanism, it is usually found on the front edge of the glove box itself.
On a 2002 Saturn SL, the ABS relay switch is typically located in the under-hood fuse box. To find it, open the hood and look for the fuse box, which is usually near the driver's side. The relay will be labeled on the cover of the fuse box, and you may need to consult the owner's manual for the exact location and identification of the ABS relay within the box.
You can find the starter relay switch in the fuse box. The starter relay switch will be one of the relay switch is in the third column. The exact location should be listed on the inside cover of the fuse box.
no switch, just relay and fuse in fuse box under hood.
--ANSWER-- If you can't find the switch in your fuse box, look under the hood, (probably near the battery), for a black plastic box with a flip-up lid. This is the power distribution box. The flasher swithc is probably in there.
In a 2000 Hyundai Elantra, the rear defroster relay switch is typically located in the engine compartment fuse box. You can find the fuse box near the driver's side of the engine compartment, usually near the battery. To confirm the exact position of the rear defroster relay, refer to the fuse box diagram printed on the cover or in the owner's manual.