0
What else can I help you with?
What happens to insulation resistance when decreasing cable length?
eat dick
What ia Standard of dc loop resistance of copper cable?
It depends on the length of th cable and the diameter of the copper cable used.
What is LV cable insulation resistance acceptance value?
The minimum acceptable insulation resistance value is calculated using the following formula: Rinsulation= (Vrated + 1 ) x (304.8 / L ) Where: Rinsulation is the minimum acceptable insulation resistance value, in mega-ohms; Vrated is the rated voltage of the cable (typically printed on the cable), in kilovolts; and L is the length of the cable, in meters (if the cable length is in feet, replace the number 304.8 with 1000).
How much is1.5 sqmm per unit resistance of a cable?
The resistance of a 1.5 sqmm cable depends on its material (usually copper or aluminum) and its length. For copper, the typical resistance is about 12.1 ohms per kilometer, while for aluminum, it’s around 19.5 ohms per kilometer. To find the resistance per unit length, you would divide these values by 1000 to get ohms per meter. Thus, the resistance of a 1.5 sqmm copper cable is approximately 0.0121 ohms/meter.
How do you calculate volt drop with length and resistance?
cable length multiply with the design current and multiply again by mV/A/m (check on site guide) then devide it by 1000. then u will get the volt drops. BY; MAMERGA
What happens to insulation resistance when increasing cable length?
The insulation resistance remains the same throughout the entire length of the conductor.
What happens to insulation resistance when decreasing cable length?
eat dick
What will happens to current when cable length increases?
With a constant voltage and increase in wire length will increase the end to end resistance and therefore the current will decrease.
What happens if a lengthy cable is connected to a load?
resistance will increase because we know that resistance is directly proportional to length.AnswerThe increase in resistance will cause an increase in the voltage drop along the cable; if this is excessive, then a cable with a greater cross-sectional area must be used to compensate. Howto choose an appropriate cable for a given length can be determined from the relevant wiring regulations for your country.
What happens to the resistance when the length is double?
whenever the cable lengthened so is the resistance, their proportional to each other
What is the relationship between insulation resistance and length of conductor in transformers?
when length is increased insulation resistance of cable is decresed i.e.,R is inversely proportional to L where R is resistance L is length
What ia Standard of dc loop resistance of copper cable?
It depends on the length of th cable and the diameter of the copper cable used.
What is insolation resistance?
I think you mean 'insulation resistance'. This is exactly what it says it is, it is the resistance between opposite sides of an insulator or dielectric. It is in the order of megohms and, in the case of a cable, is inversely proportional to its length -i.e. the longer the cable, the lower its insulation resistance.
What is LV cable insulation resistance acceptance value?
The minimum acceptable insulation resistance value is calculated using the following formula: Rinsulation= (Vrated + 1 ) x (304.8 / L ) Where: Rinsulation is the minimum acceptable insulation resistance value, in mega-ohms; Vrated is the rated voltage of the cable (typically printed on the cable), in kilovolts; and L is the length of the cable, in meters (if the cable length is in feet, replace the number 304.8 with 1000).
A coaxial cable consists of two concentric long hollow cylinders of zero resistance the inner radius a the outer radius b and the length of both is l with l and gt and gtb.?
The resistance of the coaxial cable is determined by the resistivity of the material and the dimensions of the cable (length, inner radius, and outer radius). In this case, since the cylinders have zero resistance, the resistance of the coaxial cable would also be zero. This is an idealized scenario that does not take into account real-world factors such as imperfections in the material or connections.
How much is1.5 sqmm per unit resistance of a cable?
The resistance of a 1.5 sqmm cable depends on its material (usually copper or aluminum) and its length. For copper, the typical resistance is about 12.1 ohms per kilometer, while for aluminum, it’s around 19.5 ohms per kilometer. To find the resistance per unit length, you would divide these values by 1000 to get ohms per meter. Thus, the resistance of a 1.5 sqmm copper cable is approximately 0.0121 ohms/meter.
Define the thermal resistance of a cable?
No. Conductor resistance is. Cable insulation resistance to ground is inversely proportional to its length. The longer the cable, the more leakage path to ground; therefore, the lower the insulation resistance to ground.
