0
What is a simple circuit with one or two inputs and one output?
Wiki User
∙ 14y ago
The following are definitely examples of a simple circuit:
-A resistor hooked across a battery
-A lit bulb
The following might be examples of a simple circuit:
-A Logic gate has one or more inputs and one or more outputs but is not necessarily a simple circuit within the chip containing it.
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
What is encoder explain in brief?
An encoder is a digital circuit which accepts one of the inputs and converts it into BCD or Binary Coded Output. It performs the reverse function of that of a decoder.
Design a Combinational circuit that has three input and one output the output is 1 when the binary value of the input is less than three the output is logic 0 otherwise?
If you are talking combinations, without binary number representations, then you are talking about a circuit that has a 1 output when any input is a 0. That is a 3 input NAND gate. If you are talking binary number representation, then you are talking about a circuit that has a 1 output when the inputs are 010, 001, or 000. Use a 3 to 8 decoder, with an OR gate on the low three outputs.
How does the operational amplifier work?
The operational amplifier is a device with two inputs, and one output. One input is called non-inverting, while the other is called inverting. Sometimes, there are two outputs, in which case one is also non-inverting and the other inverting. Within the limits of the design of the operational amplifier and its circuit, the output will assume whatever state is necessary to make the two inputs equal to each other. The output goes in the same direction as the non-inverting input, or in the opposite direction as the inverting input. Note that for the operational amplifer to work correctly, there needs to be some kind of feedback loop, usually from output to inverting input (we call this negative feedback), so that the output can track one of the two inputs in the ratio of the bridge that is setup in the circuit design.
Difference between Nor and Nand gate flip flops?
NAND is Not AND, meaning that if both inputs are true, the output is false.Any other combination (Including 0 0) does not change the output and it remains true. It's the opposite of AND, in which both inputs must be true for the output to be true.NOR is Not OR. If at least one input is true, the output will be false.It's the opposite of OR, where the output is true if at least one input is true.The main difference is that NOR requires at least oneinput being true to make the output false, where NAND requires both to be true.
What is offset null in lm741?
When using the LM741, one of the inputs will have a bias (usually non-inverting input), which means the output can never be 0 V. If a 0 V output is needed, you need to offset the bias. To do this, you can connect both inputs to two 1K resistors in parallel, or both inputs to either side of a 10K potentiometer. This will allow an output of 0 V from the opamp.
Introduction multiplexer demultiplexer?
A multiplexer, commonly referred as an input selector, is a circuit with many inputs but only one output: it has some data inputs, control inputs and one output, depending on the control inputs, one input from the data inputs is sent to the output .A demultiplexer is a circuit with one data input, few control inputs and many outputs, it is also known as output selector.
What is transmission Gate circuit?
It has 3 inputs. They are source, n gate, p gate and only one output that is drain
What is a AND circuit?
An AND circuit is a circuit that takes two or more inputs, and generates an output that is the boolean AND function of those inputs. Two light switches in series, for instance, is an AND circuit because both switches have to be on for the light to be on. If the switches were wired in parallel to each other, and then in series with the light, that would be an OR circuit.
There is a circuit using there nand gates with two inputs and one output find the output?
A "Nand" gate is an "And" gate with an "Inverter" added to its output. To get a logic 1 output from a "Nand" gate, you need a logic 0 on both of its inputs. If I understand your question correctly, you have three "Nand" gates. Presumably the outputs of two of them are connected to the inputs of the third. Logic 1 at both inputs of the first two "Nand" gates will produce a logic 0 output from both of them. The two logic 0's are fed to the inputs of the third "Nand" gate producing a logic 0 output from the third "Nand" gate.
Multiplier is also know as data selector why?
A multiplier is a digital circuit that performs multiplication of two numbers. It is not typically referred to as a data selector. A data selector, also known as a multiplexer, is a digital circuit that selects one of several inputs and routes it to the output. It is called a data selector because it selects which data input to use and sends it to the output. A data selector has several inputs and a single output, and it is controlled by a set of select signals that determine which input to route to the output. The data selector is used to choose between multiple inputs and can be used to implement functions such as Boolean logic or arithmetic operations. In summary, a multiplier is a circuit that performs multiplication, while a data selector is a circuit that selects one of several inputs and routes it to the output. These are two different types of digital circuits that serve different functions.
What is encoder explain in brief?
An encoder is a digital circuit which accepts one of the inputs and converts it into BCD or Binary Coded Output. It performs the reverse function of that of a decoder.
Op-amp working principle characteristics?
1.You can see that A and B are inputs and C is the output. Whenever two inputs are given , the output is the difference of the inputs. So it is called as Operational Amplifier. 2.When one input is one or Inverting or minus and the other being plus, then the output will be negative.
What is a standard single logic gate?
A logic gate is an elementary building block of a digital circuit. Most logic gateshave two inputs and one output. ... The following illustration and table show the circuit symbol and logic combinations for an AND gate. (In the symbol, the input terminals are at left and the output terminal is at right.)
What is a xor gate?
An XOR gate is an Exclusive OR gate. The output is 1 if either one or the other inputs are 1. but remains at 0 if both inputs are 1.A normal OR gate will output 1 if both inputs or either is at 1.XOR means exclusivly OR, one or the other but not both.
Device a circuit to perform OR logic using only NOR gate?
Use two NOR gates. Tie the output of the first to both (or all) inputs of the second. A logic one at any input of the first produces a logic one at the output of the second which is a standard OR.
Distinguish between combinational logic and sequential logic?
A combinational circuit's output depends only on its current inputs. This means, it has a truth table. A sequential circuit's output depends on its previous inputs. This means, it's output will depend on which state it is.
AND 20013 and 222692?
The binary AND operation has two inputs and one output.The binary AND operation will always produce a 1 output if both of its inputs are 1 and will produce a 0 output if one or both of its inputs are 0.In binary20013 = 100111000101101222692 = 110110010111100100When you perform an AND on these you get17444 = 100010000100100
