A: At a particular frequency it could be zero.
but the impedance is nearly 2000
Different answer: I built a 1/2 omni antenna for 20 meters (14.3mhz). To keep the impedance 50 ohms, I used the standard trick for a half wave, I angled the ground radials(3) to 120 degrees. It worked well. I then tested it at other bands to see how well it performed with the antenna tuner. For a very narrow little spot on the 10 meter band it was usable without the tuner. I considered that part of the band as too dangerous to be tuned practically, the slightest change, due to wind, on the radial angle would damage my equipment .
We usually only consider using dipole antennas that are an odd multiple of wavelengths. Full wave dipoles ar referred to as folded antennas. 180 degrees=300 ohms=6:1 baulin. (Aligning the radio for a different impedance is a good old trick.)
A full-wave loop antenna can be interchanged with a folded dipole without much difference. The input impedance is similar and the only difference is in the directivity: a full wave loop radiates along the axis of the loop, while a vertical folded dipole is omnidirectional.
effective height of half wave dipole antenna
The impedance of a centre fed dipole at resonance is about 73 ohms. The feed impedance of a folded dipole is four times that, 292 ohms. The feedpoint is of course balanced in both cases, thus 300 ohm balanced line is an excellent match for the folded dipole active element of a commercial TV antenna.
The polar pattern for a half lambda aerial is a toroidal (doughnut) shape with the aerial in the centre of the toroid when mounted in free space a half wave above the ground. The half wave is an omni-directional aerial and produces zero gain.
Its resonant frequency is where its length is half a wavelength, so for 100 MHz the wavelength is 3 metres and a 1.5-metre long dipole is resonant. A dipole antenna can be used for many applications within a band of 10-20% around the resonant frequency.
A full-wave loop antenna can be interchanged with a folded dipole without much difference. The input impedance is similar and the only difference is in the directivity: a full wave loop radiates along the axis of the loop, while a vertical folded dipole is omnidirectional.
effective height of half wave dipole antenna
There are several kinds of dipole; the most common is the half-wave dipole. Its total length is fairly close to half the wavelength of the design frequency. The length needs to be adjusted slightly to compensate for the thickness of the elements and for end-effects. If the length is wrong by ten or twenty percent it will alter the feed impedance, but have little effect on the gain.
The radiation resistance of a half-wave folded dipole is typically around 300 ohms. This value is higher compared to a regular half-wave dipole due to the increased current distribution along the folded elements.
The impedance of a centre fed dipole at resonance is about 73 ohms. The feed impedance of a folded dipole is four times that, 292 ohms. The feedpoint is of course balanced in both cases, thus 300 ohm balanced line is an excellent match for the folded dipole active element of a commercial TV antenna.
The dipole side is always 50 ohm. The other side depends on the signal source impedance requirement, like 8 ohms for audio.
Walter K Kahn has written: 'Currents on generalized Yagi structures' -- subject(s): Antenna arrays, Antennas, Dipole, Dipole Antennas, Impedance (Electricity)
To make an 11-meter 1-2 wave dipole antenna, cut two equal lengths of wire, each measuring approximately 5.5 meters (18 feet), which corresponds to half the wavelength at 27 MHz, the frequency used in the 11-meter band. Attach these wires to a center insulator, ensuring they are spread apart to form a "V" or horizontal shape. Connect the feedline to the center of the dipole, ensuring proper impedance matching for optimal performance. Finally, securely mount the antenna as high as possible for better signal propagation.
The characteristic wave impedance of a waveguide is defined as the ratio of the electric field (E) to the magnetic field (H) for a propagating electromagnetic wave within the guide. For rectangular waveguides, this impedance can be expressed as ( Z = \frac{E}{H} = \frac{1}{\eta} \sqrt{\frac{1}{\epsilon_r}} ) where (\eta) is the intrinsic impedance of the medium, and (\epsilon_r) is the relative permittivity. The value of the characteristic impedance varies depending on the waveguide's dimensions, operating mode, and the dielectric material used. Generally, it does not correspond directly to free space impedance, which is approximately 377 ohms.
The characteristic impedance of a transmission line is the ratio of voltage to current of the propagating electrical wave. The line input impedance is the result of the superposition of forward and reverse, or reflected waves when the terminating impedance is not adapted. If the line is infinite, nothing returns from its end and only the forward wave exits. The voltage to current ratio is then the line characteristic impedance. Remark that the same occurs when the line is terminated by its characteristic impedance, the forward wave finds a perfect continuity to the load and no energy is reflected back to the line. A matched line is like an infinite line when looked from the input terminals. Long real lossy lines also act as infinite lines for the energy of the reflected wave is dissipated along the line before reaching the source.
A: As cable lenght increases the impedance changes with frequency especially at half wave lenght where at some frequency the impedance can be zero. The impedance is a function of capacitance inductance and resistance in the cable
For a voltage standing wave ratio (VSWR) of 1.0, the source impedance, load impedance, and transmission line characteristic impedance must be matched. To calculate actual VSWR, you need to know these three values. You're question only supplies one (50 ohm line). Review wikipedia's writeup on "standing wave ratio" to glean an understanding of what you're asking about.