what is the value of the smallest division on a ammeter
An ammeter's coil requires very little current for full-scale deflection (fsd). So, to measure a current above its fsd value, most of that current must be allowed to bypass the coil. This is achieved by placing a very low value shunt resistance in parallel with the coil ('shunt' is an archaic word for 'parallel').
An ammeter has to measure to current flowing through the circuit. Resistance offers an obstruction to the current flow. So, if the resistance of an ammeter is large , the current measured by the ammeter will be quite less as compared to the actual amount of current flowing through the circuit which is undesirable. If ammeter has zero resistance , then it will give the exact value of current. But this is not practically possible because every material has some value of internal resistance which we can't control. For this reason , ammeter must have small resistance
because lots of current is likely to be flowing through them.however a shunt ammeter is easier to build than the direct ammeter as described above. in a shunt ammeter you use an ordinary meter wound with fine wire and put a small value shunt resistor across it to take almost all the current.
an ideal ammeter has zero or negligible resistance when this is connected in series no effective resistance would be added in the circuit so that the value of curret that we get is exactly of the circuit only. but when the ammeter is connected in parllel as it has zero resistance , the resistor to which it is connected in parllel gets shorted and due to his the effective resistance of the circuit is changed and so the effective current ... due to this the w=value measured by the ammeter would be different (incresed due to dec. in effective resistance)
A multimeter combines the functions of an ammeter, voltmeter, and ohmmeter and, so, can be used to measure current, voltage, and resistance by selecting the appropriate scale/setting.
what is the value of the smallest division on a ammeter
The scale division of an ammeter refers to the value each division represents on the scale of the meter. It is typically chosen based on the range and precision of the measurement required. For example, if an ammeter has a scale division of 0.1 A, each division on the scale represents 0.1 ampere.
Least count of voltmeter is the value of one division on the scale. Formula is: Least count = Range/No. of divisions For example, if a voltmeter can measure from 0 to 40 V, and it has 100 divisions in total on the scale, then its least count is 40/100 = 0.4V
The least count of an ammeter is the smallest value of current that can be measured by the instrument. It is typically determined by the scale divisions marked on the device and is an important factor in accurately reading and interpreting the measured current values.
The least count of a vernier scale is calculated by dividing the smallest division on the main scale by the total number of divisions on the vernier scale. This calculation gives the value of one vernier division.
LC FOR VERNIER CALIPER-0.1mm LC FOR MICROMETER -0.01 mm L.C- NO OF SMALLEST DIVISION ON MAIN SCALE ------------------------------------------------------- TOTAL NO OF DIVISION ON VERNIER SCALE
The absolute uncertainty of a screw gauge measurement is typically the smallest division on the scale divided by 2. This value represents the smallest increment in measurement that can be confidently distinguished using the device.
The least count of an odometer is determined by the smallest division or increment that the odometer can measure. To find it, look at the smallest digit on the odometer scale; for example, if the odometer's smallest division is 0.01 km, then its least count is 0.01 km. This value indicates the minimum distance the odometer can accurately record.
To read a linear scale, start by identifying the smallest division marked on the scale, which represents the unit of measurement. Then, observe the position of the pointer or the object being measured relative to the scale. Count the full divisions from zero to the pointer, and add any additional fraction of the next division if applicable. This will give you the total measurement value.
The least count of a beam balance depends on the divisions marked on the scale. It is the smallest weight that can be measured using the balance. It is generally calculated as the value of one scale division divided by the total number of divisions on the scale.
The value of each main scale divisions is half a degree(30') . The number of vernier scale divisions is 30. 29 main scale divisions are divided into 30 vernier scale divisions (30 VSD = 29 MSD ) Therefore value of 1 VSD = 29/30 MSD. Least Count (L.C.) = 1MSD - 1VSD = 1MSD - 29/30 MSD = 1/30 MSD = 1/30 x 30' (L.C.) = 1' (1 minute)
The difference between one main scale division and one vernier division is called vernier constant. this is the minimum length which can be measured accurately with the help of a vernier calipers. it is also called the least count of a vernier. Value of one main scale division is "1 mm" and value of one vernier scale division is "0.9 mm".So,the value of vernier constant is "1-0.9=0.1 mm".