0
Which common electronic components is not found in an integrated circuit?
Wiki User
∙ 15y ago
Inductors
Wiki User
∙ 15y ago
Add your answer:
Earn +20 pts
How does an integrated circuit work?
Integrated circuit also called as chips or microchips is a miniaturized electronic circuit made in a thin substrate of semiconductor materials. It consists mainly of semiconductors and passive components of the circuit.
A common cause of failure of electronic circuit boards is due to?
dry solder joints
How do you generate sinusoidal voltage?
The most common ways are:Mechanically, by placing a coil in a rotating magnetic field, or a rotating coil in a fixed magnetic field. This is how AC power is generated.Electronically, using an oscillator circuit. This is how sinusoidal waveforms are produced in all sorts of electronic equipment.
What is cascade tripping?
It's when a failure of one circuit leads to another circuit to fail. This can be intentional,for protection purpose, or it may not be intentional. Cascade tripping is common in sequenced circuit.
Application of a common - collector amplifier circuit?
Common collector amplifier can be used as a voltage buffer and in impedance matching
How does an integrated circuit work?
Integrated circuit also called as chips or microchips is a miniaturized electronic circuit made in a thin substrate of semiconductor materials. It consists mainly of semiconductors and passive components of the circuit.
What is chip the common nickname for?
Integrated Circuit
How is an integrated circuit manufactured?
In an integrated circuit, electronic components such as resistors, capacitors, diodes, and transistors are formed directly onto the surface of a silicon crystal. The process of manufacturing an integrated circuit will make more sense if one first understands some of the basics of how these components are formed. Even before the first IC was developed, it was known that common electronic components could be made from silicon. The question was how to make them, and the connecting circuits, from the same piece of silicon? The solution was to alter, the chemical composition of tiny areas on the silicon crystal surface by adding other chemicals, called dopants. Some dopants bond with the silicon to produce regions where the dopant atoms have one electron they can give up. These are called N regions. Other dopants bond with the silicon to produce regions where the dopant atoms have room to take one electron. These are called P regions. When a P region touches an N region, the boundary between them is referred to . This boundary is only 0.000004 inches (0.0001 cm) wide, but is crucial to the operation of integrated circuit components.
When was the Integrated circuit invented?
1958. It came into common use in the early 1970s.
Is super glue safe on electronics?
Super glue is safe on parts of electronic devices. Plastic casings and small components can be held to circuit boards for instance. This is a common method of repair if yuo are careful.
What are the most common uses for electronic enclosures?
They house electronic components, equipments, and devices. They are used to protect personnel from accidental injury.
A common cause of failure of electronic circuit boards is due to?
dry solder joints
What is the difference between computer devices and computer?
A device is a generic term for any man-made object that has moving parts. A computer is an example of a device, but not all devices are computers.A computer is a programmable machine designed to sequentially and automatically carry out a sequence of arithmetic or logical operations. The particular sequence of operations can be changed readily, allowing the computer to solve more than one kind of problem.An electronic component is any physical entity in an electronic system used to affect the electrons or their associated fields in a desired manner consistent with the intended function of the electronic system. Components are generally intended to be connected together, usually by being soldered to a printed circuit board (PCB), to create an electronic circuit with a particular function (for example an amplifier, radio receiver, or oscillator). Components may be packaged singly or in more complex groups as integrated circuits. Some common electronic components are capacitors, inductors, resistors, diodes, transistors, etc. Components are often categorized as active (e.g. transistors andthyristors) or passive (e.g. resistors and capacitors).
When would you use a series and when would you use a parallel circuit?
* The most common applications for series circuits is in Christmas tree lights and putting a fuse in series with delicate electronic equipment. * Each component in a circuit causes a voltage drop. Therefore, the series circuit should only be used where the voltage drop does not interfere with the proper functioning of the components in the circuit. * On the other hand, where all of the compenents in a circuit require the same supply voltage, then a parelell circuit should be used.
Where did microchips com from?
http://en.wikipedia.org/wiki/Integrated_circuitIn electronics, an integrated circuit (also known as IC, microcircuit, microchip, silicon chip, or chip) is a miniaturized electronic circuit (consisting mainly of semiconductor devices, as well as passive components) that has been manufactured in the surface of a thin substrate of semiconductor material. Integrated circuits are used in almost all electronic equipment in use today and have revolutionized the world of electronics....Integrated circuits were made possible by experimental discoveries which showed that semiconductor devices could perform the functions of vacuum tubes, and by mid-20th-century technology advancements in semiconductor device fabrication. The integration of large numbers of tiny transistors into a small chip was an enormous improvement over the manual assembly of circuits using discrete electronic components. The integrated circuit's mass production capability, reliability, and building-block approach to circuit design ensured the rapid adoption of standardized ICs in place of designs using discrete transistors. There are two main advantages of ICs over discrete circuits: cost and performance. Cost is low because the chips, with all their components, are printed as a unit by photolithography and not constructed one transistor at a time. Furthermore, much less material is used to construct a circuit as a packaged IC die than as a discrete circuit. Performance is high since the components switch quickly and consume little power (compared to their discrete counterparts), because the components are small and close together. As of 2006, chip areas range from a few square mm to around 350 mm², with up to 1 million transistors per mm². The integrated circuit was conceived by a radar scientist, Geoffrey W.A. Dummer (1909-2002), working for the Royal Radar Establishment of the British Ministry of Defence, and published at the Symposium on Progress in Quality Electronic Components in Washington, D.C. on May 7, 1952.[1] He gave many symposia publicly to propagate his ideas. Dummer unsuccessfully attempted to build such a circuit in 1956. The integrated circuit can be credited as being invented by both Jack Kilby of Texas Instruments[2] and Robert Noyce of Fairchild Semiconductor [3] working independent of each other. Kilby recorded his initial ideas concerning the integrated circuit in July 1958 and successfully demonstrated the first working integrated circuit on September 12, 1958.[2] Kilby won the 2000 Nobel Prize in Physics for his part of the invention of the integrated circuit.[4] Robert Noyce also came up with his own idea of integrated circuit, half a year later than Kilby. Noyce's chip had solved many practical problems that the microchip developed by Kilby had not. Noyce's chip, made at Fairchild, was made of silicon, whereas Kilby's chip was made of germanium. Early developments of the integrated circuit go back to 1949, when the German engineer Werner Jacobi (Siemens AG) filed a patent for an integrated-circuit-like semiconductor amplifying device [5] showing five transistors on a common substrate arranged in a 2-stage amplifier arrangement. Jacobi discloses small and cheap hearing aids as typical industrial applications of his patent. A commercial use of his patent has not been reported. A precursor idea to the IC was to create small ceramic squares (wafers), each one containing a single miniaturized component. Components could then be integrated and wired into a bidimensional or tridimensional compact grid. This idea, which looked very promising in 1957, was proposed to the US Army by Jack Kilby, and led to the short-lived Micromodule Program (similar to 1951's Project Tinkertoy).[6] However, as the project was gaining momentum, Kilby came up with a new, revolutionary design: the IC. The aforementioned Noyce credited Kurt Lehovec of Sprague Electric for the principle of p-n junction isolation caused by the action of a biased p-n junction (the diode) as a key concept behind the IC.[7] See: Other variations of vacuum tubes for precursor concepts such as the Loewe 3NF.
What is the difference between parallel and series?
If you are referring to an electrical circuit, a series circuit is wired in such a way that if one object is removed from the circuit, the circuit is broken and everything within the circuit loses power. In a parallel circuit different components of the circuit can be removed without disabling power to the rest of the devices within the circuit.
Is capacitor a linear device?
Capacitors are linear components. A linear component is an electronic component that has a linear relationship with current or voltage in an electronic circuit. Resistors are the most common example of linear components, along with capacitors and inductors. Linear components refer to components whose output and input have a proportional relationship. For example, the relationship between the voltage across the metal resistance element and the current can be considered to be linear when the temperature remains unchanged. Metal conductors and electrolytes also have this characteristic. Electronic components have a lot of this relationship. Poor-quality components will appear "linear distortion" under certain circumstances, that is, in such a case, the input quantity and the output quantity no longer satisfy the linear relationship. JYH HSU(JEC) Electronics Ltd (or Dongguan Zhixu Electronic Co., Ltd.) has over 30 years in the electronic components industry. Our factories are ISO 9000 and ISO 14000 certified. If you're looking for electronic components, welcome to visit our official website.
