0
Why the sending end voltage is less than receiving end voltage in case of load with leading power factor?
Wiki User
∙ 12y ago
The voltage is attenuated by the resistance in the media used for transmission. This is regardless of the power factor.
Wiki User
∙ 12y ago
Add your answer:
Earn +20 pts
What does zero leading power factor mean?
A 'leading' power factor indicates that the load current is leading the supply voltage. Since power factor is the cosine of the angle by which the load current either leads or lags the supply voltage (i.e. the load's phase angle), a cosine of 0 corresponds to a phase angle of 90 degrees. So, a power factor of 0 (leading) indicates that the load current is leading the supply voltage by 90 degrees, which means that the load must be purely capacitive.
What happens when lagging Power Factor changes to leading PF?
when lagging Power Factor changes to leading PF, then the voltage across the circuit in which capacitor bank is connected, is increased.
What are the advntage of the leading power factor?
A leading power factor means that the current is leading the voltage. That means that in the AC cycle (50 or 60 Hz) the current reaches its peak before the voltage. The amount of phase-lead can be up to 90 degrees which means one quarter cycle, or 5 milliseconds in a 50 Hz system.
What is difference between 0.8 leading and 0.8 lagging power factors?
Power factor measures the phase difference between voltage and current. If they are in phase the Power Factor is one. If the current and voltage are out of phase the power factor is between zero and one. You can describe the PF by saying the current lags the voltage with a PF = .8 or the voltage leads the current with a .8 PF.
What are the disadvantages of leading power factor?
When you have a Power Factor less than 1 the voltage and current waveforms in an AC circuit are out of phase. Therefore at any given instant of time the work being done or energy being expended is calculated by multiplying the current x voltage. This reduces the wattage at any instant of time. When the Power Factor is one the instantaneous multiplication of the current and voltage would yield the maximum value with the waveforms in phase. This is much easier to see with a picture, but imagine a square wave for both voltage and current. Say for half the cycle the current is 2A and Voltage 3V and for the second half of the cycle both are zero. So for 1/2 the cycle the watts generated are 6 watts and zero for the second half of the cycle. Now if the two waveforms were 180 degrees out of phase the voltage would be zero when the current was 2A and the current would be zero when the voltage was 3V for zero watts. In this case the Power Factor would be zero.
Leading and lagging power factor?
The terms, 'leading' and 'lagging' refer to what the load current is doing, relative to the supply voltage (Phase difference) -never the other way around. If the current is leading the voltage, then the power factor is 'leading'; if the current is lagging the voltage, then the power factor is 'lagging'.
What does zero leading power factor mean?
A 'leading' power factor indicates that the load current is leading the supply voltage. Since power factor is the cosine of the angle by which the load current either leads or lags the supply voltage (i.e. the load's phase angle), a cosine of 0 corresponds to a phase angle of 90 degrees. So, a power factor of 0 (leading) indicates that the load current is leading the supply voltage by 90 degrees, which means that the load must be purely capacitive.
Why does the terminal voltage increase in leading load?
due to decrease in power factor
What types of loads have a leading power factor?
Capacitive loads have a leading power factor. Current leads voltage when there is capacitive reactance. (The opposite is inductive, which is lagging.)
Define voltage regulation and efficiency of a short transmission line?
Voltage Regulationvoltage regulation of a line is defined as the change in voltage at the receiving end when full load at a given power factor is removed, the voltage at the sending end being kept constant. it is expressed as a fraction or a percentage of the receiving end voltage at full load. it can be written as, Per unit regulation = Vrnl - Vrfl / VrflPercent regulation = (Vrnl -Vrfl / Vrfl) * 100Efficiency of a Short Transmission LineIt is the ratio of the Power Output of the line to the Power Input of the line.
What happens when lagging Power Factor changes to leading PF?
when lagging Power Factor changes to leading PF, then the voltage across the circuit in which capacitor bank is connected, is increased.
Why power factor lags?
When there is an inductive element in the circuit, the current lags behind the voltage. an ideal inductor will make the current lag behind the voltage by 90 degrees..a capacitive element on the other hand will make the current lead the voltage (ideally by 90deg). That's why capacitors in parallel with the system are used a lot for power factor correction
What are the advntage of the leading power factor?
A leading power factor means that the current is leading the voltage. That means that in the AC cycle (50 or 60 Hz) the current reaches its peak before the voltage. The amount of phase-lead can be up to 90 degrees which means one quarter cycle, or 5 milliseconds in a 50 Hz system.
What is difference between 0.8 leading and 0.8 lagging power factors?
Power factor measures the phase difference between voltage and current. If they are in phase the Power Factor is one. If the current and voltage are out of phase the power factor is between zero and one. You can describe the PF by saying the current lags the voltage with a PF = .8 or the voltage leads the current with a .8 PF.
What determines leading or lagging power factor?
underdampedAnswerA lagging power factor describes a situation in which the load current is lagging the supply voltage. This describes an inductive load, such as a motor, etc.
What are the disadvantages of leading power factor?
When you have a Power Factor less than 1 the voltage and current waveforms in an AC circuit are out of phase. Therefore at any given instant of time the work being done or energy being expended is calculated by multiplying the current x voltage. This reduces the wattage at any instant of time. When the Power Factor is one the instantaneous multiplication of the current and voltage would yield the maximum value with the waveforms in phase. This is much easier to see with a picture, but imagine a square wave for both voltage and current. Say for half the cycle the current is 2A and Voltage 3V and for the second half of the cycle both are zero. So for 1/2 the cycle the watts generated are 6 watts and zero for the second half of the cycle. Now if the two waveforms were 180 degrees out of phase the voltage would be zero when the current was 2A and the current would be zero when the voltage was 3V for zero watts. In this case the Power Factor would be zero.
What actually the power factor is?
Power factor is the cosine of the angle by which the current leads or lags the voltage in an a.c. circuit. It can also be defined as the ratio between a load's true power (expressed in watts) and its apparent power (expessed in volt amperes).Power factor is designated as 'leading' or 'lagging' which is determined by whether the current is leading or lagging the supply voltage. Leading currents are associated with resistive-capacitive circuits, whereas lagging current are associated with resistive-inductive circuits.
