This figure only applies to sinusoidal waveforms. It is derived, as the name 'rms' implies, by finding the square-root of average value of square of the instantaneous currents over a complete cycle.
A: Peak voltage is RMS multiplied by a factor of 1.41
Conversions of RMS voltage, peak voltage and peak-to-peak voltage. That are the used voltages. The expression "average" voltage is used for RMS voltage.Scroll down to related links and seach for "RMS voltage, peak voltage and peak-to-peak voltage".Answer'Average' is not the same as 'root mean square'. As the average value of a sinusoidal voltage is zero, you cannot convert it to a peak-to-peak value.
When people talk about 480V systems, they mean 480 is the RMS voltage.
ANSWER: The peak to peak voltage can be found by multiplying 120 v AC x 2.82= 339.41
P-P voltage = RMS voltage * 2 * sqrt (2)Here's an example: house voltage is 120VRMS, which is actually ~169 volts peak - neutral. double this will give peak to peak value.
No, the peak-to-peak voltage is 2sqrt(2) times as much as the rms for a pure sine-wave.
A: Peak voltage is RMS multiplied by a factor of 1.41
Peak voltage will be 1.414 times the RMS. Peak to Peak voltage, assuming no DC offset, will be 2 x 1.414 x the RMS value.
Its 0.7 times peak-0 voltage, 106 mv RMS.
The average voltage is the rms voltage.Volts peak = volts RMS times 1.414Volts RMS = volts peak times 0.7071Use the link below to an RMS voltage, peak voltage and peak-to-peak voltage calculator.********************************The average voltage is not the r.m.s. voltage.The average voltage of a sine wave is 0.636 x the peak value. Conversely, peak voltage is 1.57 the mean or average.
RMS stands for "Root of the Means Squared", and is a mathematical method of defining the "operating" voltage of a sine wave power source. Typical home lighting and outlet voltage presently is 120 VAC (volts alternating current), 60 Hz. (Hertz, formerly referred to as "cycles per second".) But the PEAK voltage is the absolute maximum voltage at the "peak" of each sine wave of voltage. Mathematically, the "Peak" voltage is 1.414 (which is the square root of the number 2) times the RMS voltage, and conversely, the RMS voltage is 0.707 times the PEAK voltage.
rms stands for root mean squared. rms voltage is a way of measuring a sort of average alterating current voltage as distinguished from peak-to-peak voltage. Likewise for ac rms current.
That is an electric AC or audio output, where the voltage is measured in volts rms. Scroll down to related links and look for "dB conversion (decibel)". Look there in the middle at this headline: "RMS voltage, peak voltage and peak-to-peak voltage".
Conversions of RMS voltage, peak voltage and peak-to-peak voltage. That are the used voltages. The expression "average" voltage is used for RMS voltage.Scroll down to related links and seach for "RMS voltage, peak voltage and peak-to-peak voltage".Answer'Average' is not the same as 'root mean square'. As the average value of a sinusoidal voltage is zero, you cannot convert it to a peak-to-peak value.
I am not certain what is being asked here. RMS is Root Mean Square which is basically the DC voltage which would produce the same amount of heat in a heating element as the AC voltage in question. Since AC is continuously changing in polarity and voltage, it is handy to use the RMS voltage rather than the peak (169.7V for 120V RMS) or peak-to-peak (339.4V for 120V RMS). The peak or peak-to-peak voltage is handy to know when considering the maximum values such as in rectification.
Another name for average voltage is the RMS (Root Mean Square). This is a voltage derived from the peak to peak voltage multiplied by .707. If the peak to peak voltage is 170 volts then the average voltage (RMS) would be 170 x .707 = 120 volts.
When people talk about 480V systems, they mean 480 is the RMS voltage.