0
In the Z-parameter Equations the independent parameters are Currents i.e., i/p And O/p .
therefore to find any of the parameter(Z11,Z12,Z21,Z22) We have to either open circuit the input or the output port .as we are open circuiting any one of the port the Z-parameters Are called as open circuit parameters
Got It !
Clear!
What else can I help you with?
Why low power factor wattmeter is used for open circuit test of transformer?
For open circuit test of transformer, the secondary is open circuit and the circuit impedance is largely inductive due to the core impedance having high L as compared to R. hence the power factor is reduced, thus , we use low power factor wattmeters.
What is a circuit path called that has a break in it preventing current from flowing?
That's an "open" circuit.
What is the difference between an open and a short?
An open (circuit) is where insufficient (often zero) current flow where some is expected. In this case, little or no work is done. A short (circuit) is where high (often infinite or as limited by the power supply) current flows where only some is expected. In this case also, little or no work is done by the device intended, but there is enough current to trip (or blow) the protective device (fuse or circuit breaker).
What happens when a circuit has a gap in it?
When a circuit has a gap in it, everythig stops working because the electricity wont be able to flow around the whole circuit
How do you calculate h parameters?
v1= h11 i1 + h12 v2 i2= h21 i1 + h22 v2 To calculate h11 and h21 short circuit the output terminals & to calculate h22 and h12 make input open. Substitute values in the above equation to find h parameters.
Impedance inversion may be obtained with?
Impedance Inversion in Microwave circuits can be obtained by utilizing the Short Circuit or Open Circuit Transmission line of proper length.
Why low power factor wattmeter is used for open circuit test of transformer?
For open circuit test of transformer, the secondary is open circuit and the circuit impedance is largely inductive due to the core impedance having high L as compared to R. hence the power factor is reduced, thus , we use low power factor wattmeters.
Why is an open circuit called open?
An open circuit is called open because the circuit has an opening, a disconnection. In other words, there is an open space in the circuit in which the electrons cannot move through.
Prove that capacitor will be open circuit if dc souce is applied?
the impedance of the capacitor is given by Xc=1/jwC where w=2*pi*f and for DC source f=0 hence Xc=infinity ie, the capacitor will provide infinite impedance for DC, or its Open circuit
What is a break in an electrical circuit called?
A break in an electric circuit is called an open circuit. Electric current will not flow through an open circuit.
What is the earth wire inside a plug for?
This wire provides a low impedance return path to the distribution panel in case of a circuit fault. This direct fault current path will trip the circuit's breaker and open the circuit.
A loop with a break in it that prevents current from flowing is called?
an open circuit.
What will be the impedance of a C-R circuit consisting of a resistance of 20ohm and capacitance 2microfarad when it is connected to direct current?
In a direct current (DC) circuit, a capacitor will eventually charge up and act as an open circuit, meaning it will not allow current to flow after reaching full charge. As a result, the impedance of a resistor-capacitor (C-R) circuit under DC conditions is simply the resistance value. Therefore, the impedance of the given C-R circuit with a resistance of 20 ohms and a capacitance of 2 microfarads is 20 ohms.
What is a circuit in which electricity doesn't flow called?
In a lighting circuit an open circuit will turn off the light.
What is the circuit called when it is disconnected?
open
What is the symbol for a open circuit?
When a circuit is in off condition then it is called an open circuit..
What is through a discontinuous circuit which no current can flow?
meaning that the current from your power source doesn't return to the positive end (electricity flows from - negative, to + positive)
