0
What else can I help you with?
What is the basis of using 550 Volts for equipment in underground coal mines?
what is the basis of Your
What is easier to measure volts amps or watt?
If you have the right test equipment amps are the easiest to measure. A slip over the wire amp meter is easier to use than a clamp on amp meter. The other two values have to be measured by using test leads from the test equipment.
Can 230VAC single phase supply be used on a circuit that demands 208VAC single phase?
A unit of electrical equipment is designed for operation at a certain voltage - or within a certain range of voltages - i.e for 5 volts, 12 volts, 120 volts. 220 to 240 volts. Originally the UK household alternating current supply voltage was specified at 240 volts or, more precisely, 240 volts RMS +/-6%, running at a frequency of 50Hz.Some time ago, to allow harmonisation across Europe, the specifications were changed to 230 volts RMS +10%/-6%, also running at a frequency of 50Hz.Thus the mains supply voltage will remain within European Union norms (standards) even if it varies between an upper limit of 253 volts and a lower limit of 216.2 volts. So, because 208 volts is lower than the minimum range of a standard 230 volt 50 Hz supply, it is not safe to assume that any equipment which has a rating plate saying that it should be powered from a 208 volts ac supply can be used on a 230V ac supply without causing any damage. Such damage might affect the equipment itself or its surroundings or its "human" users... If the Asker could use the discussion page - by clicking the Open Discussion button shown below this answer - to tell us exactly what the circuit is, which "demands 208VAC single phase", that information would be interesting to know. Then, maybe, a much more helpful answer could then be given here!
Can you supply 100 amps using 1.5 volts?
No
What tool do you use to measure watts?
If you use this formula W = Amps x Volts you will not need any tools. Using equipment nameplates will give you both values. If nameplates are inaccessible then you need a volt meter and an amp meter to obtain these values.
What is the basis of using 550 Volts for equipment in underground coal mines?
what is the basis of Your
Will i damage a piece of equipment if i give it too many volts?
Yes you will.Each piece of equipment is designed to work on a specific voltage. Wrong voltages applied to it will destroy the equipment.
What other voltage can replace a 9 volts adapter's to a 9 volts equipment?
If the manufacturer specifies that a certain voltage is needed for their equipment, then that is the voltage that must be applied to it. To do otherwise may ruin the equipment and void the manufacturer's warranty.
Will a 1.55 volt battery damage something that runs on 1.5 volts?
Using a 1.55 volt battery in a device that runs on 1.5 volts should not damage the device. Most devices have a tolerance for slight voltage variations. However, it may affect the performance or lifespan of the device over time.
How many volts can damage an electronic component?
30 volts of ESD
Is sj cord rated for 300 volts to be used for 480 volt?
No, SJ cord is only rated for 300 volts and is not suitable for use with 480 volts. It is important to use the correct voltage rated cord for safety and to prevent damage to equipment. Look for cords that are specifically rated for 480 volts.
Your volt meter shows your generator is producing 145 volts will it damage your electrical equipment?
Yes it coudl damage equipment. Check voltage rating on equipment. However, there should be an adjustment somewhere on the generator to set the voltage properly. Also make sure your meter is calibrated. Check a known voltage source such as an outlet and compare readings.
How do you prevent damage to equipments when 215 volts becomes 440 volts?
and breakers that can only hold up to 250 volts
What can you run on ten amps?
At 120 volts you can operate any equipment up to 1200 watts. At 240 volts you can operate any equipment up to 2400 watts.
Why telecom equipment used 48v?
48 volts is a convenient safe voltage to use, and telephone systems use a positive earth connection to minimise electroytic damage ot cables.
Why should you not use a transformer made for a clothes dryer for an answerin machine?
A transformer made for a clothes dryer is designed to handle higher power loads, typically 240 volts, which is much higher than what an answering machine requires (usually 120 volts). Using such a transformer can potentially damage the answering machine due to the higher voltage output. It is important to match the transformer's specifications with the device's power requirements to avoid any safety hazards or equipment damage.
Convert 600 dc volts into ac volts?
This action takes inverter equipment that is explained in the link below.
