0
What else can I help you with?
How do you design a cascade connection counter?
If an 8 bit binnery counter chip is used a 8 input and gate is connected to the output of the counter and the output of the and gate is connected to the clock input of the next chip so that when the first counter get to 11111111 all outputs of the counter will be high and it will pulls the second counter once and the first counter will return to 00000000 and count again from 0 to 255 des. THIS IS NOT THE PROPER ANSWER I WAS SEARCHING FOR I NEED THE RIGHT ANSWER.
What is collector bypass capacitor?
A: It is not a bypass it is a negative feedback to effect the input voltage, Bias is when a DC voltage is applied to insure proper operation
Troublshooting a low power output complaint on cummins?
Start by verifying proper fuel system operation, then check compression output on individual cylinders.
What is the purpose of program counter?
program counter is a register that has the address of next instruction that has to be executed after currently executing instruction. it is used for proper execution of functions of computer by providing address of next instruction to microprocessor.
What is the proper way to run a condensate drain with a trap Does it need a vent?
The condensate drain on the a-coil should have a trap and the trap should be vented for proper operation . The vent should rise above the top edge of the drain pan in the unit. Their should be a capped clean out before the vent.
Which direction is proper when passing a serving bowl?
counter clockwise. thats how i do it at least...
Which way should you turn the water valve on the washer to ensure proper operation?
To ensure proper operation of the washer, turn the water valve clockwise to open it and counterclockwise to close it.
Do you turn clockwise or counter clockwise to change an edger blade?
To change the blade on an edger, you typically turn it counterclockwise to loosen and tighten it clockwise once the new blade is in place. Be sure to consult the manufacturer's instructions for the specific model you are working with to ensure proper handling.
What is the proper direction to traverse a cul-de-sac in Kentucky?
Same way as it is in any country which drives on the right - right to left, a.k.a., counterclockwise.
How can I install a folding barn door for my closet?
To install a folding barn door for your closet, you will need to measure the opening, purchase a barn door kit, attach the track to the wall above the closet, hang the door panels on the track, and adjust the hardware for smooth operation. Follow the manufacturer's instructions carefully for proper installation.
In the US and Canada is the flow from pool returns clockwise or counter-clockwise?
If you have your left hand on the skimmer basket or the inlet side of the pump, and you have your right hand on the return side of the filter or the clean water going back to the pool then the flow will be clockwise.
How do you take the tension off the serpentine belt on 1998 Buick Park Avenue?
Put the proper size wrench or socket on the pulley of the tensioner.Pull the wrench counter clockwise to release the tension on the belt.
What is the right spinning direction for the blades on a 4 motor drone?
Many drones use counter-rotating blades (some spinning clockwise, some counter-clockwise) to improve lateral control. It is easy to determine the proper blade spin direction: it is the one that blows air downward for any given motor. If it blew air upward, the drone would never leave the ground.
Do you have to vent an electric dryer for proper operation?
No, you do not have to vent an electric dryer for proper operation.
What is the proper plug wire sequence on the distributor cap for a 1969 Pontiac 8 cylinder 400?
1-8-4-3-6-5-7-2 Distributor rotates counter clockwise
How do you loosen the screws on a VGA cable?
Use the proper type screw driver to match the screw heads and turn counter clockwise. For you digital people out there that do not have a watch with hands, the top of the screw head turns left.
How can I properly hang folding closet doors?
To properly hang folding closet doors, follow these steps: Measure the opening to ensure the doors will fit properly. Install the track at the top of the closet opening. Hang the doors on the track using the provided hardware. Adjust the doors for proper alignment and smooth operation. Secure the doors in place and test for smooth opening and closing.
