answersLogoWhite

0

Yes, but the secondary coils function by induced magnetic currents- they have no wired connection to the rest of the apparatus. In some cases , on railroad ( big leagues,here not Lionel) There are controls in the cab that can pre-selected transformer functions- for example when starting the let-down from high speed running, the engineer will call off: Primary Coils- Half Flux- thus makes a peculiar noise, the transformer seems to be yawning, Thus it is ( set) for a lower gear, without ,say changing the throttle setting. There are usually only two settings for the Transformer output- Half flux and Full Flux, and an overhead switch controls this. Boy does this bring back memories.

User Avatar

Wiki User

12y ago

What else can I help you with?

Continue Learning about Engineering

When working on a current transformer the secondary windings must be?

When working on a current transformer the secondary windings must be shorted. <<>> Properly loaded


If a step-up transformer is to increase voltage it needs?

A step-up transformer needs more turns on the secondary windings than on the primary windings to increase the voltage.


Load test on single phase transformer?

The dc tests that can be done on a transformer are to measure the resistance of each windings and to measure the insulation resistance between the windings and between each winding and the transformer case.


What is the purpose of the primary windings of a transformer?

The primary windings of a transformer are responsible for receiving the input voltage from the power source. When an alternating current flows through these windings, it creates a magnetic field that induces a voltage in the secondary windings through electromagnetic induction. The primary windings essentially convert electrical energy into magnetic energy, which is then transformed back into electrical energy in the secondary windings at a different voltage level.


What causes a low voltage in the transformer?

If this refers to a wire wound transformer, as it sounds then there is likely only two possibilities : the input voltage has dropped prier to entering the primary windings or there is a short in the windings some where within.The only other possibility I can think of is : This is a trick question and the transformer is a step down transformer.

Related Questions

Why induction transformer called rotating transformer?

Transformer has windings


Is 3 phase star transformer has more winding than delta?

The # of windings in a transformer are based on the primary and secondary voltages the transformer is rated for not the way the windings are connected.


When working on a current transformer the secondary windings must be?

When working on a current transformer the secondary windings must be shorted. <<>> Properly loaded


What is the three phase transformer?

it has three primary windings & three secondary windings.


What is transformer tank?

The container the transformer core and windings are placed inside is the tank.


Is it a step up or a step down a transformer has 20 primary windings and 100 secondary windings the secondary voltage is 25v?

If a transformer has 20 primary windings and 100 secondary windings, it is a step up transformer. If the secondary voltage is 25v, the primary voltage will be 5v, because the turns ratio is 20 to 100, or 1 to 5.


If a step-up transformer is to increase voltage it needs?

A step-up transformer needs more turns on the secondary windings than on the primary windings to increase the voltage.


How do you know if transformer has copper or aluminium windings?

You can determine if a transformer has copper or aluminum windings by looking for any markings or labels on the transformer, as manufacturers often indicate the material used. You can also do a visual inspection - copper windings typically have a distinct reddish color, while aluminum windings are lighter in color. Lastly, you can use a magnet to test the windings - copper is not magnetic while aluminum is.


If a transformer has 20 primary windings and 100 secondary windings and the secondary voltage is 25 what is the primary voltage?

Transformer step-up/step-down voltage is turns-ratio, so if a transformer has 20 primary windings and 100 secondary windings (a turns-ratio of 1 to 5) and the secondary voltage is 25, then is the primary voltage is 5.


What are the physical parts of transformer?

Physicially it has transformer tank, conservator, bucholz relay , windings, oil


The leakage flux of transformer depends on?

Actually it depends on the air gap between the core and the windings of the transformer. This is the reason why stepped core is used in medium and large transformers as it decreases the air gap between the windings and the core of the transformer.


Load test on single phase transformer?

The dc tests that can be done on a transformer are to measure the resistance of each windings and to measure the insulation resistance between the windings and between each winding and the transformer case.