answersLogoWhite

0

OF Course it can ,it is named undershoot in that case .

Do a search and you will understand it better

User Avatar

Wiki User

12y ago

What else can I help you with?

Continue Learning about Engineering

What is peak to peak?

Peak to Peak is the most positive peak to the negative peak value. Or find any peak value and multiply by 2.


Is 12 volts peak to peak the same as 12 volts ac?

No. 12 volts peak to peak would be 6 in the positive polarity and 6 negative polarity. Simply saying 12 volts AC would be 12 volts in each polarity or 24 volts peak to peak


What is the peak value of wave?

it's highest swing positive or negative. 90 and 270 degrees. the peak for a 10vAC generator would be 10vAC


How to calculate the peak-to-peak value of a signal?

A: AC or our line voltage is sinusoidal in nature it goes up to a positive peak returns to zero and proceed to the negative peak. 120V AC is actually swinging from peak to peak. It is 120 volts but the peak is the 120 v times 1.41 or 169.2 volts and since it also go negative then the peak to peak 120 volts times 2.82 or 338.40 volts or twice the peak voltage


What is the Relationship between the peak-to-peak DC voltage across RL and the peak input voltage in full wave rectifier?

The input voltage, an AC Sine Wave will have a Peak-to-Peak value equal to 2X its Peak value. Once rectified, all the Peaks will be either above or below the Zero reference line. They'll look like a series of identical bumps. The net value of the unrectified voltage will be Zero. The positive and negative waveforms canceling each other out. The rectified waveform will be all positive or negative and its net value will be non-zero. Its AVERAGE value will be .636 times its Peak value. Its Root Mean Square (RMS) value will be .707 times its Peak value. Its Peak-to-Peak value will equal 1X the Peak value.

Related Questions

What is the peak overshoot in control systems means?

Peak overshoot in control systems refers to the maximum amount by which a system's response exceeds its steady-state value during a transient response. It is expressed as a percentage of the steady-state value. Peak overshoot is an important parameter as it indicates the system's stability and performance.


What is the approximate peak overshoot for a unity feedback system with damping factor 0.6?

0.0947


What is the approximate peak overshoot for a unity feedback system with a damping factor 0.6?

0.0947


What is the approximate peak overshoot for a unity feedback system with damping?

According to some references I checked, the overshoot will be:100*exp[z*pi/sqrt(1-z^2)]where "z" is the damping ratioThis is about 9.5% at z=0.6Source(s):


What is maximum overshoot time?

It is denoted by Mp . It is the normalized difference between the peak of the time response and steady output.Mp = { C(tp) - C(∞) }/ C(∞) *100


What is DC offset in signal generator?

A sine wave centered at zero will have a positive peak that is the same magnitude as the negative peak. This can be offset so the negative peak magnitude does not match the positive peak magnitude. For example a 1volt peak - neutral sine wave could be DC offset by 1 volt so the positive peak is at 2 volts and the negative peak is at 0.


What is peak to peak?

Peak to Peak is the most positive peak to the negative peak value. Or find any peak value and multiply by 2.


What is negative peak in hplc?

In HPLC, the negative peak refers to a trough or valley observed in the chromatogram where the signal intensity drops below the baseline. This can occur due to factors such as noise, interference, or improper column packing. Negative peaks can sometimes affect the accuracy and precision of peak integration and quantification in HPLC analysis.


What are the problems of open loop?

overshoot and stability


What the peak of the wave?

it's highest swing positive or negative. 90 and 270 degrees. the peak for a 10vAC generator would be 10vAC


Why is there an overshoot in action potential?

An overshoot in action potential occurs due to the rapid influx of sodium ions causing the membrane potential to become more positive than the resting potential. This depolarization phase is necessary for propagating the action potential along the neuron.


Is 12 volts peak to peak the same as 12 volts ac?

No. 12 volts peak to peak would be 6 in the positive polarity and 6 negative polarity. Simply saying 12 volts AC would be 12 volts in each polarity or 24 volts peak to peak