0
Can the overflow that holds the flapper be removed and replace the rubber gasket under it?
yes on a toilet I am guessing .. you can take the tank off the bowl and unscrew the nut of the overflow and replace the rubber seal. To make sure you wont get mad if it leaks after you put it all together is run a bead of CLEAR silicon around the new rubber seal and around your tank washers before you put it together and it will seal up any tiny holes or misalignment you have.
What else can I help you with?
Does steel seal really works on blown head gasket?
As an emergency repair yes. The only permanent repair is to replace the gasket.
How can pneumatic system trobleshoot?
Replace the rubber gasket. Inspection of air valves. Compressor control.
How do you replace the gasket between the toilet base and tank?
To replace the gasket between the toilet base and tank, first, turn off the water supply and flush the toilet to empty the tank. Disconnect the water supply line and remove the tank bolts, then carefully lift the tank off the bowl. Remove the old gasket and clean both surfaces before placing a new gasket in position. Reassemble the tank onto the bowl, reattach the bolts, and reconnect the water supply, then check for leaks.
What is CAF gasket?
Type your answer here... CAF gasket refers to Compressed asbestos fibre gasket. This gasket is carcinogenic and hence industries have started to reduce this material.
Do you use gasket glue on both sides of the gasket on a thermostat?
You can, but if you have a new gasket glue is really not needed.
How can I replace a bathtub overflow gasket?
To replace a bathtub overflow gasket, you will need to remove the overflow cover plate, unscrew the old gasket, clean the area thoroughly, and then install the new gasket by screwing it into place. Finally, reattach the overflow cover plate.
When fixing a blown head gasket do you have to replace the manifold gasket on a 1991 Nissan pickup truck?
If it was removed then YES.
What is the easiest way to replace a head gasket on a 1991 GSI Storm?
There is only one way to replace the 1991 Storm head gasket. anything in the way of getting to the head has to be removed (intake, hoses, etc..) Then the valve cover and head will have to be removed to change the gasket.
Water runs out on the floor when toilet is flushed?
Replace /bulb / flapper /disc and check the over flow tubeA:The kits are inexpensive and come with the float and the flapper assembly.
How do I perform a bathtub overflow gasket replacement?
To perform a bathtub overflow gasket replacement, first, remove the screws holding the overflow cover in place. Then, take out the old gasket and clean the area thoroughly. Install the new gasket and reattach the cover. Finally, test for leaks by filling the tub with water.
American standard Toilet gasket leaks?
wax ring on bottom leaking to the floor needs to be replaced if it is a leak inside the tank flapper needs to be replace this problem occurs a lot if you use Bleach in your tank the rubber flapper gets soft
What is the purpose of the overflow drain gasket in a sink or bathtub?
The overflow drain gasket in a sink or bathtub serves to prevent water from leaking out of the overflow opening and helps to maintain the proper water level in the fixture.
How repair head gasket KIA carnival 2004 v cc?
Just like any other vehicle. The head must be removed in order to replace the gasket. There is no other repair for a blown head gasket except the replace it.
How do you replace the valve cover gaskets on a 2003 Jeep Liberty?
To replace the valve cover gaskets on a 2003 Jeep Liberty, the valve cover is removed. The old gasket is then removed from both the valve cover and the manifold (old gasket will come off in pieces on both sides). Then spread the sealant on the manifold, place the new gasket on, then put sealant on top of the gasket and replace the valve cover and bolt down.
How do you replace a head gasket on a 1995 altima?
Intake & exhaust manifold must be removed. Then the head must be removed. head inspected for cracks or warping, and new head gasket installed. Not a repair for a novice.
How do you replace the oil pan gasket for a 01VW passat 1.8t?
To replace the oil pan gasket on a 2001 Volkswagen Passat turbo the exhaust downpipe must be removed. The oil needs to be drained and all the pan bolts need to be removed as well. When replacing the gasket a sealer should be used to ensure a proper seal.
Why does your 1994 suzuki rm 125 smoke from the radiator overflow?
If you are getting exhaust smoke coming out of the radiator overflow, you need to replace the head gasket that seals the cylinder from the cylinder cap where your coolant runs through to cool the engine.
