answersLogoWhite

0

Yes, should be no problem.

User Avatar

Wiki User

16y ago

What else can I help you with?

Continue Learning about Engineering

How do you fix a copper pipe that burst?

There are many ways to fix a burst pipe, if you are experienced in soldering you could re round the pipe closing the burst portion and solder the cracked section, or simply cut the burst section out and solder in a new piece withe two couplings. For the less experienced I would recommend cutting the pipe and using a shark bite repair fitting, it comes with detailed instructions and is made just for the situation you described


What am I doing wrong when I can't get the solder to stick when soldering a copper pipe?

Not cleaning the pipe or joint enough, not using flux, or not heating the pipe or joint enough. You use the blue tip of the flame on the joint and the capillary action sucks the solder into the joint. You have to clean the pipe with sandpaper or steel wool, the joints with a fitting brush on the inside, and use a proper flux and solder.


How do you weld copper pipe to copper pipe - not brazed?

tig or mig depending on the wall thicknessCopper to copper is either soft soldered, or silver solderedSilver solder is a bad term as "solder" normally means lead content according to the AWS


How do you connect copper pipe?

YOU thread or braze copper pipe Copper tubling you solder, braze, flaire, compression ring, mechincal joints


How do you solder a copper pipe end?

Clean the end of the pipe and whatever kind of fitting you are putting on it with either steel wool or fine sandpaper. Put flux on both pieces covering all the surface where they will be joined. Use a propane torch and heat on one side of the fitting and touch the solder on the opposite side. When the solder gets hot enough to melt, it will be drawn to the heat source. By having the solder on the opposite side from the heat you know there is solder completely around the fitting. Let it cool before handling.

Related Questions

how do weld GI pipe to GI pipe?

A GI pipe is welded to a GI pipe by using solder and flux. The pipe is heated up, flux applied, and then solder allowed to flow into the joints to create a secure bond.


What type of solder should be used for copper pipe?

For copper pipe, lead-free solder is recommended to ensure safe and effective connections.


How do you properly solder a copper pipe?

To properly solder a copper pipe, first clean the pipe and fitting with emery cloth. Apply flux to both the pipe and fitting, then heat the joint with a propane torch. Once the joint is hot enough, touch the solder to the joint and let it flow around the connection. Allow the joint to cool and wipe away any excess solder.


Are solder joints mechanically too weak?

Depends on the solder used. If silver solder is used it is actually stronger than the pipe itself.


How do you fix a copper pipe that burst?

There are many ways to fix a burst pipe, if you are experienced in soldering you could re round the pipe closing the burst portion and solder the cracked section, or simply cut the burst section out and solder in a new piece withe two couplings. For the less experienced I would recommend cutting the pipe and using a shark bite repair fitting, it comes with detailed instructions and is made just for the situation you described


What would you use to solder a shut off valve on to a copper pipe?

What to use to solder a shut off valve


How can I fix a copper pipe?

To fix a copper pipe, you can use a pipe cutter to remove the damaged section, clean the ends of the pipe, and then solder a new piece of copper pipe in place using a propane torch and solder. Be sure to follow proper safety precautions and techniques when working with a torch.


What am I doing wrong when I can't get the solder to stick when soldering a copper pipe?

Not cleaning the pipe or joint enough, not using flux, or not heating the pipe or joint enough. You use the blue tip of the flame on the joint and the capillary action sucks the solder into the joint. You have to clean the pipe with sandpaper or steel wool, the joints with a fitting brush on the inside, and use a proper flux and solder.


How can I effectively solder a copper pipe?

To effectively solder a copper pipe, first clean the pipe and fittings with emery cloth. Apply flux to the cleaned surfaces. Heat the joint evenly with a propane torch. Once the joint is hot enough, apply solder to the joint. The solder will melt and flow into the joint, creating a strong bond. Allow the joint to cool before testing for leaks.


How do you get water out of a pipe in order to solder copper pipes?

First off, you should shut off the water source. Then you must drain the pipe. After that you can clean up the area to be soldered, apply some flux. Now you are ready to solder. The pipe doesn't need to be bone dry, since it will dry as you solder from the heat.


What is the average cost to solder a copper pipe?

$135 per hr


How do you get the pipe to stop leaking while you solder?

You can put a ball of white bread inside of the pipe it will stop the water longe enough to solder the joint then it will deteriate and come out of the pipe if you have an aerator on the faucet check it to make sure that the bread does net clogg the screen