You remove the existing tub shoe and related fittings and install a new assembly. In some cases a reciprocating saw will be needed to cut the shoe flange located inside the tub
A cast iron tub is about 325lbs. steel is about 75lbs. Tap on tub if it sounds solid it is cast iron.
Usually. Going through the overflow drain gets you straight into the drain without having to make the sharp bend in the tub drain. There could be a trap that comes apart in the drain underneath if it is accessible.
If the condition is decent and it is extra deep and long over $3,500
A right-hand drain applies usually to bath-tubs and means the drain is on YOUR RIGHT when you are standing in front of the tub.
Yes It just takes them a Little longer to drain in the unlikely event that they all drain at the same time.
To replace a tub drain, you will need to remove the old drain using a drain removal tool or pliers. Then, clean the area around the drain and apply plumber's putty to the new drain before inserting it into the tub. Tighten the new drain securely using a drain wrench, and test for leaks by running water into the tub.
To replace the drain in your tub, you will need to first remove the old drain by unscrewing it counterclockwise. Then, clean the area around the drain and apply plumber's putty to the new drain before inserting it into the tub. Finally, tighten the new drain by turning it clockwise until it is secure.
A cast iron tub is about 325lbs. steel is about 75lbs. Tap on tub if it sounds solid it is cast iron.
To replace a pop-up tub drain, you will need to unscrew the old drain, remove it, and then install the new drain by following the manufacturer's instructions. Make sure to use the appropriate tools and sealants for a proper installation.
To replace a tub drain and overflow, you will need to remove the old drain and overflow assembly using a drain key tool. Then, install the new drain and overflow assembly by following the manufacturer's instructions. Be sure to seal the connections properly to prevent leaks.
A steel tub is typically lighter and more affordable than a cast iron tub. Cast iron tubs are heavier and more durable, but also more expensive. Cast iron tubs retain heat better and are known for their classic look, while steel tubs are easier to install and maintain.
To replace a tub drain plug efficiently and effectively, follow these steps: Use a screwdriver to remove the old drain plug. Clean the drain area thoroughly to remove any debris or buildup. Purchase a new drain plug that fits your tub's drain size. Apply plumber's putty around the new drain plug before inserting it into the drain. Tighten the new drain plug securely using a wrench. Test the new drain plug by filling the tub with water to ensure it seals properly.
To replace a tub stopper, you can unscrew the old stopper and remove it from the drain. Then, insert the new stopper into the drain and screw it in place. Make sure it fits securely to prevent water from leaking.
yes
The piece in the drain is screwed into the drain under the tub It is usually corroded and is not going to unscrew. You can use a sawsall or jig saw to cut the drain in 3 or 4 places around the opening and peel the piece out. You can also disconnect the drain under the tub and just leave it on the tub. There should be access to the back side of the tub. Usually a panel or door in the back of a closet that is in the room beside the bath. If there is no access, you will need to make one so that you can connect the drain to the new tub.
The main differences between a steel tub and a cast iron tub are their durability and weight. Cast iron tubs are heavier and more durable, while steel tubs are lighter and may be more prone to chipping. For a bathroom renovation project, the choice between a steel tub and a cast iron tub depends on your priorities. If you prioritize durability and are willing to handle the weight, a cast iron tub may be the better choice. However, if weight is a concern and you are looking for a more affordable option, a steel tub may be a better fit for your project.
You step on the plug in the drain? The plug is part of the trim ring and screws into the drain. It seals the drain to the bottom of the tub. You can remove it and replace the drain completely, but you can't take out the plug.