0
To turn on the subwoofer using a Pioneer MOSFET 50Wx4 amplifier, first ensure the amplifier is properly connected to the power source and the audio system. Then, connect the subwoofer to the amplifier’s designated output terminals. You may need to adjust the amplifier settings, such as gain and crossover frequency, to optimize performance. Finally, make sure the head unit or receiver has a subwoofer output enabled to send the appropriate signal to the amplifier.
What else can I help you with?
How do you connect a motor to a picaxe 18M?
It depends. If you only want to turn the motor in one direction, then you could simply use a medium power mosfet (eg:IRF530) connected to an output pin on the PICAXE, and with a backward diode around the motor. If you need to change direction, it's best to use an L293D, which allows independent bidirectional control of two motors.
Transformer shorted turn fault?
? Are you asking about a transformer turn to turn fault? Or if a transformer is shorted, does this turn into a fault? Please clarify the question.
Do you turn faucet counter clockwise to turn on?
no, clockwise
How do you turn the heat off?
Turn your thermostat to 40*. That oughta do the trick. I have tried that and it did not go off the onle way to turn it off now is to turn the car off
How do you restart all the programs on your computer?
turn it off... then turn it on again.
How do you turn the light down on a pioneer mosfet 50 x 4?
200[ans]
How do you use the aux on a Pioneer Mosfet 50wx4?
Turn off the player, hold down the function button until it turns on taking you to a menu letting you set the time etc. Keep pressing the function until you get to the aux option, turn it on by pressing the up key. Then start the unit and press the mode button, you should now have CD, Tuner and Aux available. :-)
Construction of mosfet in depletion region?
To make a depletion MOSFET, the channel must be doped with carriers; this is in total opposite to an enhancement MOSFET which avoids carriers in the channel at all cost. (because the carriers in the channel become the subthreshold leakage current) Since you need to pinch the channel against the substrate to guarantee to turn off the channel completely, there must be a reverse bias between the substrate and the source terminal. As a result, the source terminal of an N type depletion MOSFET must be tied to Vdd. This is also a complete opposite to enhancement MOSFET. In order to turn off the channel quickly, the carriers in the channel of depletion MOSFET are usually planted shallowly. This is a drastically different from enhancement MOSFET that carriers must be planted deeply into source terminal in order to support a large diffuse current. The construction of depletion MOSFET thus requires far less diffusion time than enhancement MOSFET.
How do you keep from blowing a new subwoofer?
turn down the gain or the bass
How do you turn up bass on a Sony STR-K7000?
There is a dial on the back of the subwoofer to adjust the bass.
Why Power cannot be switched on in mitsun mit-x4 home theter?
turn on the switch behind the subwoofer
What is the remote wire blue on a car stereo for?
it provides a signal to your subwoofer amplifier to turn it on and off with the car's key
How do you turn your sub woofer on in 2001 Mercury mountaineer?
To turn on the subwoofer in a 2001 Mercury Mountaineer, first ensure the vehicle's audio system is properly connected and powered. Check the amplifier settings, if applicable, to ensure it's activated. Adjust the audio settings on the vehicle's head unit to enable the subwoofer output. If the subwoofer still does not work, verify all connections, including power, ground, and signal wires.
How do you set time on pioneer deh 1000?
with the car on turn the pioneer off and then press and hold the func button until the menu displays
What is a verb of pioneer?
The verb form of "pioneer" is "to pioneer." It refers to the act of being a trailblazer or innovator in a particular field or area, often by introducing or developing new ideas, technologies, or methods.
How do you get skullcandy skullcrushers bass to work?
Put a battery into the Subwoofer/Bass Amplifier. If you look, there should be a slide opening in the side of the Subwoofer adjuster. In the package there should have been a battery included (inside the protective leather bag). Future recommendation: read the instructions that come with the headphones :P Enjoy your extra bass ;) P.S. You also have to turn the Subwoofer "on." There's a switch on the side of the adjuster.
Why does your sub woofer only turn on with the radio and not for your bluetooth input?
Because of the blue power remote wire leading from your head unit to your subwoofer amplifier acts like a light switch. When you turn your head unit(stereo) on it turns on your amp powering the subwoofer but if you use blue tooth the unit is designed for talking not for bass so it will not send sound signal to the subs.
