Starting of the synchronous motor using the DC generator creates a magnetic field.
In synchronous motor hunting can be minimized using flywheel to the shaft .
There are 5 types of starting in induction motors: 1) resistance variable method 2) auto transformer method 3) slip ring induction motor method Squirrel cage induction motor using two types of starting methods 1.Direct on line starter 2.Star delta starter
The synchronous speed of a motor can be calculated using the formula: ( \text{Synchronous Speed} (N_s) = \frac{120 \times f}{P} ), where ( f ) is the frequency in hertz and ( P ) is the number of poles. For a four-pole motor connected to a 50Hz supply, the synchronous speed is ( N_s = \frac{120 \times 50}{4} = 1500 ) RPM. Thus, the synchronous speed of the motor is 1500 revolutions per minute.
If you use synchronous generator... you need rotor to rotate always in synchronous speed... practically it s not possible always to produce that speed by air flow... Air flow always varies...But using induction generator, you need to get speed to make slip as positive value.. it is always possible...so induction generator is best one..
If I'm understanding the question, you are proposing using one motor and one generator, and have the motor spin the generator up to speed, and have the generator attempt to supply power to the motor. The answer is yes, you can do this, but you will be losing energy, not gaining it. The motor and generator's efficiencies are less than 100%, so once you remove the outside source they will slow down until they come to a complete stope, without any other load connected other than themselves.
In synchronous motor hunting can be minimized using flywheel to the shaft .
There are 5 types of starting in induction motors: 1) resistance variable method 2) auto transformer method 3) slip ring induction motor method Squirrel cage induction motor using two types of starting methods 1.Direct on line starter 2.Star delta starter
A synchronous condenser (also known as a synchronous capacitor or synchronous compensator) is a DC-excited synchronous computer (large rotating generators) whose shaft is now not connected to any using equipment.
The synchronous speed of a motor can be calculated using the formula: ( \text{Synchronous Speed} (N_s) = \frac{120 \times f}{P} ), where ( f ) is the frequency in hertz and ( P ) is the number of poles. For a four-pole motor connected to a 50Hz supply, the synchronous speed is ( N_s = \frac{120 \times 50}{4} = 1500 ) RPM. Thus, the synchronous speed of the motor is 1500 revolutions per minute.
If you use synchronous generator... you need rotor to rotate always in synchronous speed... practically it s not possible always to produce that speed by air flow... Air flow always varies...But using induction generator, you need to get speed to make slip as positive value.. it is always possible...so induction generator is best one..
Synchronous generators are traditionally driven at a constant speed to maintain the fixed frequency of the generated electricity. However, with advancements in power electronics and control systems, it is possible to drive a synchronous generator at variable speeds by using technologies like electronic converters to adjust the frequency of the output power to match the grid.
the self control of a synchronous motor is done using an inverter fed through a dc link.speed is controlled by varying the output frequency of the inverter by controlling the dc link voltage
Yes, a sump pump can be connected to a generator to make it operate. Keep in mind that the starting current of the pump motor could be 300% of the running current and the sizing of the generator should take this into account. If you are looking for the sump pump using a mechanical connection it will connect to the engine and not to the generator.
If I'm understanding the question, you are proposing using one motor and one generator, and have the motor spin the generator up to speed, and have the generator attempt to supply power to the motor. The answer is yes, you can do this, but you will be losing energy, not gaining it. The motor and generator's efficiencies are less than 100%, so once you remove the outside source they will slow down until they come to a complete stope, without any other load connected other than themselves.
To answer this question the voltage of the motor is needed.
When the slip value (s) equals 0, it means that the rotor speed is equal to the synchronous speed of the motor. In this case, the output torque can be calculated using the formula T = (P * 60) / (2 * π * Ns), where T is the torque, P is the number of poles, and Ns is the synchronous speed. The speed of the motor is the synchronous speed in this condition.
A device called a power inverter.In old vacuum tube radios an electromechanical device called a vibrator was used.Another device is a motor-generator using a DC motor and an AC generator.