answersLogoWhite

0

Three Phase conversion from KW to Amps, but you have not supplied enough info. Use whatever formula below works with the rest of the data you have.

E =VOLTS P =WATTS R = OHMS I =AMPS HP = HORSEPOWER

PF =POWER FACTOR KW = KILOWATTS KVA = KILOVOLT-AMPS

EFF = EFFICIENCY (decimal)

When P, E and PF are known: P / E x PF x 1.73

When HP, E, EFF and PF are known: HP x 746 / E x EFF x PF x 1.73

When KW, E and PF are known: KW x 1000 / E x PF x 1.73

When KVA and E are known: KVA x 1000 / E x 1.73

User Avatar

Wiki User

15y ago

What else can I help you with?

Continue Learning about Engineering

Will a 10 hp 220 volt motor draw large amounts of electricity?

A single phase 10 HP motor will draw aproximately 50 amps. A three phase 10 HP motor will draw aproximately 28 amps.


Are all large motors three-phase?

Yes, most large motors are three phase. Usually single phase motors only go up to 10 HP. Larger than this and the wire size and contactors used to control the motors becomes extreme. For example a single phase 10 HP motor on 115 volts draws 100 amps. The same single phase motor on 230 volts draws 50 amps. The same 10 HP motor on three phase system draws the following amperage; 230 volts is a 28 amp draw, 460 volts is a 14 amp draw and 575 volts is a 11 amp draw. As you can see the higher the voltage becomes, the smaller the wire feeder size is needed and much smaller size contactor can be used to control the motor.


Why do you try to balance single phase loads on a three phase four wire system?

Because all electrical supply systems are designed to A specific amperage delivery. If you are set up for 1000 amps 3 phase, That means that you are getting 350 amps each on three legs. If you put all your single phase (110volt) stuff on the same leg and have A total of 300 amps of draw then when you try to use several 110 volt items and A three phase piece you will draw too much power on one leg causing an overload. Even though you may only be using A total of 400 amps. Something will give, Most likely the fuse or breaker.


How many amps does a 5 hp 208 volt 3 phase motor draw?

read the name plate on the motor


How much current will a 15 hp single phase 220 volt fan motor draw?

The wiring should allow for 115 amps.

Related Questions

Will a 10 hp 220 volt motor draw large amounts of electricity?

A single phase 10 HP motor will draw aproximately 50 amps. A three phase 10 HP motor will draw aproximately 28 amps.


If 5000 watts operates 230 volts three phase what will it draw in amps?

21.739 a 21.739 a


How many amps will a 20 KW heat strip draw on 480 volt three phase?

24 amps. This could be three 11.54 resistors connected in star, or three 34.6 ohm resistors connected in delta.


What amperage will a range with a rating of 12.9 kw draw?

This depends on what voltage the range is rated for and if it is single phase or three phase. At 220 volts single phase it is about 60 amps, 240 v single phase , 53 amps and at 480 v three phase about 15 amps.


How many amps does a 3 phases 600 volt 10 hp draw?

Assuming the power factor is 1, a 10 hp motor operating at 600 volts in a three-phase system would draw approximately 13.33 amps.


How many amps per phase would a machine rated at 460 amps over three phases take?

It depends on the internal circuit of the machine. If it is star operated its full load current will be same as rated current. If it is Delta operated its full load per phase current will be as given below : Phase current = Line Current / 1.732


What is the phase current of a three phase 2.2kw 415v motor connected in star?

The line current would be the same if the motor were connected in delta. The current can be based on the rule of thumb which says 7 amps must be allowed for a 1-HP single-phase motor on 240 v. A 2.2 kW motor is three times as powerful, and on a three-phase supply of the same voltage (240/415) it would draw 7 amps.


What you basically want is will each phase take 26 Amps current for 15HP 3 phase 415VAC motor?

Yes, for a 15HP 3-phase 415V AC motor, each phase will draw approximately 26 Amps of current when running under normal operating conditions. This results in a total current draw of 26 Amps per phase for the motor.


How many amps does a 2000 watt heater draw at 240 volts on each line?

For a single phase circuit, the equation you are looking for is I = W/E. Amps = Watts/Volts.


How many amps does a 30HP motor use hooked to 480v 3 pH 60Hz line?

The electrical code states that a 30 HP induction motor at 460 volts three phase will draw 40 amps. <<>> I = 33.34 AMPS IF EFF.= 95% AND P.F.= 85%


How much amperage does a dishwasher draw?

Each electrical equipment draws a different amperage. Most residential dishwashers draw about six amps. There has to be a specification sticker on the inside of the door of the dishwasher ,which must such information stated on it. Commercial dishwashers could draw sixty amps and be using three phase power!!


How many amps for 1hp 3phase?

For a 1hp 3-phase motor, the current draw will depend on the voltage supply. Typically, at 230V, a 1hp 3-phase motor will draw around 3.6 amps. However, this value may vary based on the motor efficiency and power factor.