answersLogoWhite

0

Horsepower is a rating of power, and power is equivalent to voltage times current.

Answer

The horsepower is the Imperial unit for power, whereas the volt is the SI unit for potential difference. These are two different quantities, so your question makes no sense. It's like asking how many miles per hour there are in 10 metres!

User Avatar

Wiki User

12y ago

What else can I help you with?

Continue Learning about Engineering

10 hp 208 volt 3ph 90 percent pf what is the amps squirl cage?

The formula you are looking for is I = HP x 746/1.73 x Volts x %Eff. x pf.


How many ampere in one hp?

There are 746 watts in 1 HP. Watts = amps x volts. It depends on the voltage rating of the motor. Amps = 746/volts = ? need voltage.


How many volts in a watt?

It depends on how many Amps (current) are applied to the voltage. Watt = Volts x Amps. e.g. 12 volts @ 5 amps = 60 watts


Are all large motors three-phase?

Yes, most large motors are three phase. Usually single phase motors only go up to 10 HP. Larger than this and the wire size and contactors used to control the motors becomes extreme. For example a single phase 10 HP motor on 115 volts draws 100 amps. The same single phase motor on 230 volts draws 50 amps. The same 10 HP motor on three phase system draws the following amperage; 230 volts is a 28 amp draw, 460 volts is a 14 amp draw and 575 volts is a 11 amp draw. As you can see the higher the voltage becomes, the smaller the wire feeder size is needed and much smaller size contactor can be used to control the motor.


How many amperes are there in 2hp aicondition?

To convert horsepower (hp) to amperes (A), you can use the formula: A = (hp × 746) / V, where V is the voltage in volts. For a typical air conditioner operating at 240 volts, 2 hp would be approximately 6.2 amperes (A). However, the exact current draw may vary based on the efficiency and design of the specific air conditioning unit. Always consult the manufacturer's specifications for accurate information.

Related Questions

What is max single phase hp as per nec?

The maximum single phase HP motor listed in the CEC is 10 HP. At 115 volts 100 amps and 230 volts 50 amps.


How many amp in 10 HP?

How to convert horsepower to amps? You'd have to make an assumption about volts. If it's running at 220 volts, that would make it 34 Amps. There are 746 watts in a horsepower and Amps = Watts/Volts.


How many amps does a 3 phases 600 volt 10 hp draw?

Assuming the power factor is 1, a 10 hp motor operating at 600 volts in a three-phase system would draw approximately 13.33 amps.


How much does 8 amps 110 volts equal in HP?

To convert amps and volts to horsepower (HP), you can use the formula: HP = (Volts × Amps) / 746. For 8 amps at 110 volts, the calculation would be (110 × 8) / 746, which equals approximately 0.88 HP.


How much does a 10 hp pump draw 480 volt?

A 10 hp pump operating at 480 volts would draw approximately 15.6 amps of current. This can be calculated by dividing the power in watts by the voltage.


What is the full load amps for 2.4 hp motor at 460 volts?

what is the full load amps for 2.4 hp motor at 460 volts ?


How many watts will it take to run a 120 volt 1 hp motor?

A 1 HP motor running at 120 volts will draw approximately 746 watts. This calculation is based on the formula: Watts = Volts x Amps.


How many Amps for 3 horsepower at 208 volts?

For a single phase 3 HP motor at 208 volts the amperage is 18.7 amps. For a three phase 3 HP motor at 208 volts the amperage is 10.5 amps. This figure is derived at by taking the full load amps at 230 volts and adding 10%. As the voltage goes down the amperage goes up. For 200 volt motors 15% is added to the FLA of a 230 volt motor.


In 3 horsepower how many amps needed?

3 amps on 120 volts is almost 1/2 hp. To be exact 0.48 hp, that's why I said almost 0.5 hp or 1/2 hp. So say you are thinking of buying a 3 amp grinder or table top sander and you want to know about how many HP (Horse Power) it is, the answer is 120 volts X 3 amps = 360 X 0.00134 = 0.4824 HP which is almost a 1/2 HP you can do the math from there if its a 6 amp motor then its almost a 1 HP motor or to be exact 0.4824 X 2 = 0.9648 also almost 1 HP. This is if you are on 120 volts. If you are on 110 or 125 volts its about the same.


10 hp 208 volt 3ph 90 percent pf what is the amps squirl cage?

The formula you are looking for is I = HP x 746/1.73 x Volts x %Eff. x pf.


How many volts are in 5 MeV?

1 MeV is equal to 1.6 x 10^-13 volts. Therefore, 5 MeV is equal to 8 x 10^-13 volts.


How many ampere in one hp?

There are 746 watts in 1 HP. Watts = amps x volts. It depends on the voltage rating of the motor. Amps = 746/volts = ? need voltage.