0
How many kilowatts will a motor use in 30 days if it runs constantly It is 460 volt and pulls 120 amps 3 phase?
In order to determine power from volts and amps, we need to know the power factor and efficiency, but the question did not provide that information, so I will make an educated guess that the efficiency is 0.95 and the power factor is 0.92. The actual motor nameplate ratings will have to factor into the real calculations.
460 V times 120 A is 55.2 KVA. The question did not say, but it is assumed that the 120 A is per phase, so divide by 1.732 (square root of 3) to get winding power of 31.9 KVA, and then multiply by 3 to get total winding power of 95.6 KVA. Multiply by 0.92 and 0.95 to get power in watts of 83.6 KW.
If you want to know kilowatt-hours for 30 days, multiply by 30 and 24 to get 60.2 mega watt-hours.
What else can I help you with?
What is the amperage of a 20 HP 240v single phase motor?
Typically single phase motors go up to 10hp. Wouldn't be very efficient at about 100 amps. A 20hp 3 phase motor at 230v pulls 52 amps. The 10hp single phase 230v pulls 50 amps.
What does number of pulls mean for an electric motor?
The number of pulls for an electric motor typically refers to the number of times the motor's rotor completes a full rotation or cycle during a specific period, often in relation to its operational performance. It can also indicate the frequency of electrical signals or inputs the motor receives, which can affect its speed and torque. Understanding the number of pulls helps in assessing the motor's efficiency and suitability for particular applications.
How to change the speed of a three phase motor?
A typical 2 speed three phase motor will have 6 leads on the motor windings which will require 3 contactors to incorperate both the "high" and the "low" speeps. Inorder for the motor to run on "low" speed you need to have a contactor (c1) that pulls in for the L1, L2,L3 leads... that should achieve the "low" speed of the motor.. To achieve the "high" speed you will need a contactor (c2) to shun or short L1,L2,L3 together... and another contactor (c3) to pull in the L4,L5,L6 leads... to recap ... Low speed will requrie c1= L1,L2,L3 powered by phase 1, phase 2, phase 3 of the primary source voltage. High speed requires c2 to short or shun L1,L2,L3 together while c3= L4,L5,L6 to be powered by Phase 1, Phase 2, Phase 3 fo the primary source voltages. Be sure to check for proper rotation of the motor and by reversing any 2 leads of the primary source voltage you will change the rotation for the motor. This can also be done using two contactors by having L1,L2,L3 connected to the first contactor and also the additional contacts mounted on top of the second contactor. L4,L5,L6 are connected to the second contactor. The important thing to remember is to use an interlock which fits into both contactors when they are clipped together. This stops both contactors operating at the same time!!! ( the additional contacts mount on top of a contactor and are mechanically connected to it so that they act together)
Are swamp coolers effective?
the water's latent heat of vaporization is being pulled from the air, the water pulls heat from the room to undergo a phase change.
What is the difference between a star-delta starter and a DOL starter?
At least two types of 3-phase electric motor starter are available: Direct-On-Line (DOL) and Star-Delta.For more information about how they work, and the differences between them, see the answers to the Related Questions shown below.
What is the amperage of a 20 HP 240v single phase motor?
Typically single phase motors go up to 10hp. Wouldn't be very efficient at about 100 amps. A 20hp 3 phase motor at 230v pulls 52 amps. The 10hp single phase 230v pulls 50 amps.
How many kilowatts does 7 amps pull?
Seven amps pulls zero kilowatts . W = A x V. You need to state a voltage to multiply the amperage by to get watts. Then divide by 1000 to get kilowatts.
What constantly pulls a glacier downhill?
Gravity
What size breaker for a 208 volt single phase motor that pulls 1.4 amps?
208 volts is not a common single phase voltage but you could just size your breaker to the capabilities of the conductor. 208 is normally a phase to phase voltage <<>> Many 230 volt motors can be connected to lower voltage supplies. These motors can be connected to supplies of 208 and 200 volts. The code requirement is that the 230 volt full load amperage of the motor be increased by 10% and 15% respectively for wire sizing and breaker selection. To answer the question you will need a two pole 15 amp breaker.
Which phase pulls spindle fibers apart from homologous chromosomes?
Anaphase
What does number of pulls mean for an electric motor?
The number of pulls for an electric motor typically refers to the number of times the motor's rotor completes a full rotation or cycle during a specific period, often in relation to its operational performance. It can also indicate the frequency of electrical signals or inputs the motor receives, which can affect its speed and torque. Understanding the number of pulls helps in assessing the motor's efficiency and suitability for particular applications.
How do you replace blower motor 78 firebird?
look on the firewall and there should be bolts that come out around the blower motor and then it just pulls out.
Outboard motor pulls to the right how fix?
Turn the trim tab to the left some
What does an airsoft motor do?
In AEG's or Airsoft Electric Guns the motor rotates the internal gears allowing your bb's to fire
How are the positions of the moon the Moon's phase and tidal range related?
the moon's gravity pulls waves on different phases of the moon
Why does the lower three heater speeds on a 1999 Malibu not work?
The blower motor resistor is defective. They go bad when the blower motor pulls to much amperage.
How to change the speed of a three phase motor?
A typical 2 speed three phase motor will have 6 leads on the motor windings which will require 3 contactors to incorperate both the "high" and the "low" speeps. Inorder for the motor to run on "low" speed you need to have a contactor (c1) that pulls in for the L1, L2,L3 leads... that should achieve the "low" speed of the motor.. To achieve the "high" speed you will need a contactor (c2) to shun or short L1,L2,L3 together... and another contactor (c3) to pull in the L4,L5,L6 leads... to recap ... Low speed will requrie c1= L1,L2,L3 powered by phase 1, phase 2, phase 3 of the primary source voltage. High speed requires c2 to short or shun L1,L2,L3 together while c3= L4,L5,L6 to be powered by Phase 1, Phase 2, Phase 3 fo the primary source voltages. Be sure to check for proper rotation of the motor and by reversing any 2 leads of the primary source voltage you will change the rotation for the motor. This can also be done using two contactors by having L1,L2,L3 connected to the first contactor and also the additional contacts mounted on top of the second contactor. L4,L5,L6 are connected to the second contactor. The important thing to remember is to use an interlock which fits into both contactors when they are clipped together. This stops both contactors operating at the same time!!! ( the additional contacts mount on top of a contactor and are mechanically connected to it so that they act together)
