the short answer: to distinguish as an AC transformer, as opposed to a DC transformer. The long answer: A Kva stands for Kilo-Volt-Amps. The transformers mounted on telephone poles work with hundreds of thousands of volts so rather than 750,000 V, we use the abbreviation kilo, being the metric prefix for thousand and write 750 kV. As for 'VA' some high school physics tells us Voltage*Current=Power. voltage being measured in volts (V), current in amperes or amps for short (A), and power being Watts (W). However alternating current is a very fickle beast and the voltage and current vary in a wave like fashion causing the power to reverse direction. Other factors come into play such as power sag, types of electrical loads, and wasted energy, the equation soon becomes very messy. at times the power is actually negative and is flowing away from your house! so to simplify things they use Volt-Amps to represent the maximum amount of power as an absolute value that the electricity can deliver. as opposed to the USEFUL amount of power which is lower due to resistances in the wires and other loses. Engineers have to worry about the KVA when designing a system so it can handle everything thrown at it, keeping the wires from melting and that transformer from blowing up!
...of what? to a house, to a breaker (to lower fault current level?), to an amplifier circuit?
AC voltage, like the voltage in your house, is typically referred to as 120vAC. This means the voltage swings 120V positive and 120V negative 60 times per second (60 Hz) 360 degrees total (sine wave). Current and voltage go hand-n-hand so the current alternates with the voltage. the RMS value is what we experience at the output (160vAC is actually sent to the circuits)
The voltage and current are delivered in a sine wave that goes positive and then negative at 60 cycles per second. Google sine wave to see what a sine wave looks like.
The power supply converts the high voltage (e.g. 120VAC in US, 240VAC in Europe) alternating current house electricity supply down to the various different low voltage direct current supplies needed by different devices that make up the computer. These low voltage direct current supplies are tightly regulated in the power supply circuitry to prevent transients in the house electric supply from perturbing the computer's electronics as well as to compensate for variations in power demand as the different devices that make up the computer operate.
Yes if the house supply is 220-240 volts. The required voltage range should be printed somewhere on the fan.
access current ( like plugs in your house ) direct current (like batteries)
Yes, the frequency stays the same. Only the voltage and current change as the voltage is stepped down.
Always voltage constant in parallel circuit if you look your house wiring all are in parallel therefore 220 volt present in every house but current is different
The mains to the house is an alternating current and this high voltage is stepped down using a transformer. The low voltage secondary alternating current is converted to direct current using 4 diodes wired as a bridge rectifier. The 'lumpy' direct current is smoothed using an electrolytic capacitor to smooth the resulting dc. It may need to be voltage regulated if the circuits it feeds are voltage sensitive.
its not a question of voltage but current(amps) a load calculation needs to be done to determine service size required refer to section 8 of the cec CIRCUIT LOADING AND DEMAND FACTORS section 8-200 (1)
To measure house current voltage, a digital voltmeter (DVM) is typically set to the 200V AC range. This range is suitable for measuring standard household voltages, which in the U.S. typically fluctuate between 110V and 120V. Using this range ensures accuracy and prevents damage to the meter, as it can comfortably handle the expected voltage without exceeding its limits.
120 volts A/C, or some might refer to it as house current.
Check that the input and output voltages are as required. Check that the transformer is big enough for the current required for the unit you have.
the short answer: to distinguish as an AC transformer, as opposed to a DC transformer. The long answer: A Kva stands for Kilo-Volt-Amps. The transformers mounted on telephone poles work with hundreds of thousands of volts so rather than 750,000 V, we use the abbreviation kilo, being the metric prefix for thousand and write 750 kV. As for 'VA' some high school physics tells us Voltage*Current=Power. voltage being measured in volts (V), current in amperes or amps for short (A), and power being Watts (W). However alternating current is a very fickle beast and the voltage and current vary in a wave like fashion causing the power to reverse direction. Other factors come into play such as power sag, types of electrical loads, and wasted energy, the equation soon becomes very messy. at times the power is actually negative and is flowing away from your house! so to simplify things they use Volt-Amps to represent the maximum amount of power as an absolute value that the electricity can deliver. as opposed to the USEFUL amount of power which is lower due to resistances in the wires and other loses. Engineers have to worry about the KVA when designing a system so it can handle everything thrown at it, keeping the wires from melting and that transformer from blowing up!
Yes ,it's the same voltage.You have a +-5% of voltage range
In the United States, the standard voltage for household current is 120 volts, so 123.4 volts would fall within an acceptable range. However, fluctuations in voltage can occur, so it's always a good idea to consult a professional if you are experiencing voltage irregularities.