If a 'parallel' circuit has more than one load in its (not "it's"!) branches, then it is not a parallel circuit, but a series-parallel circuit! To resolve the circuit, you must first resolve the total resistance of the loads within each branch.
Switches used in electrical circuits are wired in series with either a parallel or series load. In parallel loads, the switch is upstream from the parallel circuit, so that the switch will shut off all of the parallel circuits.
Ammeters are connected in series with the load under test. This requires the load be disconnected from the source, and the ammeter placed in circuit. Voltmeters are connected in parallel with the load under test. This does not require any circuit changes. Sorry, but WikiAnswers does not support illustrations.
To solve any D.C. circuit by using Thevenin Theorem,First of all load resistance RL is disconnected from the circuit and open circuit voltage across the circuit is calculated (known as Thevenin equivalent voltage)Secondly, the battery is removed by leaving behind its internal resistance. Now we calculate equivqlent resistance of the circuit ( called Thevenin equivalent resistance).Now we connect Thevenin Voltage in series with Equivalent resistance of the circuit and now connect load resistance across this circuit to calculate current flowing through the load resistance.Whereas in the case of using Norton theorem, we again remove the load resistance if any, and then short circuit these open terminals and calculate short circuit current Isc.Second step is same as in Thevenin theorem i.e. remove all sources of emf by replacing their internal resistances and calculate equivqalent resistance of the circuit.Lastly, join short circuit current source in parallel with equivalent resistance of the circuit. Now, we can calculate votage across the resistance which was connected in parallel with Isc.So, by knowing the open circuit voltage, we can calculate current flowing the resistance and on the other hand , by knowing the short curcuit current , we can calculate voltage across the resistance.
An ammeter is always connected in series and a vlotmeter in parallel
when loads are connected in parallel it means that they share common nodes at both the ends i-e voltage across all the loads is the same. when one of the load in such a circuit is shorted i-e its voltage is made zero volts, voltage across the other loads goes to zero because of parallel connection and they gets shorted also.
your moms a load in a parallel
A battery doesn't see a series or parallel circuit. It just supplies the current that is demanded by the load be it a series or parallel load. Visualize that a single load across a battery is both a series and parallel load to the battery.
A parallel circuit is a circuit that takes both legs to make a load.
in a parallel circuit, current get divided among the parallel branches in a manner so that the product of current and the resistance of each branch becomes same. The sum of the current in each branch is equal to the total current of the circuit.
A parallel circuit is a type of circuit where loads are connected side by side. In a parallel circuit, each load has its own path to the power source, allowing them to operate independently of each other. If one load in a parallel circuit fails, the others will continue to function.
a parallel circuit has 2 or more paths.a series circuit has 1 path.a parallel circuit is better for homes and school
If an ammeter is placed in parallel with a a load on a circuit, the circuit can short out as the ammeter takes the place of the load, flowing freely through the meter. Never measure across a resister or other electronic load with an ammeter. Remember, ammeters are used in series while voltmeters are used in parallel.
Yes.
in a parallel circuit, the relationship of resistance is thus: 1/R1 + 1/R2 = 1/RT where R1 and R2 are two resistors in parallel and RT is the total resistance in the circuit: Using this, as more branches are added, the resistance decreases This is because there is more ways for the current to flow and thus using the analogy of a water flow with a constraint on it (resistor in electrical circuits), a whole load of streams with the same constraint on each will allow more water through than one large stream with the same small constraint on it.
Switches used in electrical circuits are wired in series with either a parallel or series load. In parallel loads, the switch is upstream from the parallel circuit, so that the switch will shut off all of the parallel circuits.
In a parallel circuit an electrical load may be disconnected without affecting other loads.
Ammeters are connected in series with the load under test. This requires the load be disconnected from the source, and the ammeter placed in circuit. Voltmeters are connected in parallel with the load under test. This does not require any circuit changes. Sorry, but WikiAnswers does not support illustrations.