0
To determine the value of a resistor and capacitor in a circuit, you can use Ohm's Law (V = IR) for resistors, where you calculate resistance (R) based on the voltage (V) across and the current (I) flowing through it. For capacitors, you can use the formula (C = \frac{Q}{V}), where capacitance (C) is calculated by dividing the charge (Q) stored by the voltage (V) across the capacitor. Additionally, frequency response or time constants in RC circuits can provide insights into optimal values for specific applications. Simulation tools and empirical testing can also aid in fine-tuning component values.
What else can I help you with?
Control diagrame of a capacitor bank and why you use capacitor banks?
---- Capacitor banks used to improve power factor(lagging) of a circuit:: This is necessary since it causes saving in power and electricity bill in following ways: 1) As p.f rises, circuit currnt decreases and hence I2R losses reduce 2) Var consumption reduces There is no tool provided here to draw the ckt diagram:: U take on PFC(power factor correction bus), then connect switch fuse, then HRC fuse, then Contactor, then overload relay and finally the capacitor bank
What is AN on a transformer?
It is electronic device which pass or transform a electric energy from one ckt to anoher ckt The answer is wrong. AN denotes the cooling method of Transformer. AN means Air Natural
What is the working principle of a colpitts oscilator?
The principle of LC tank ckt. which produces 180 deg phase shift the loop gain AB=1 in hartley oscillator are used 2 inductors and 1 capacitor.
Can a 600V rated cable be use in 480V 3 Phase Ckt?
yes,
What is the procedure for measurement of true RMS Voltage?
In a non-reactive ckt, a simple measurement with an AC voltmeter is all that is needed. In a reactive ckt, you must first address power factor, which can be metered also, and combined with the apparent voltage as above to calculate true rms.
What happened when capacitor is infinite?
it works as a short ckt
Relation between voltage and current if you consider capacitor ckt?
In a capacitor ckt, current will be lead ahead from voltage by an angle 90 degree. Because for a capacitor the relationship between voltage and current is given as v=(jx)i , where v= voltage i= current jx=capacitive reactance
What will happen if a diode is connected to capacitor?
the diode when forward biased will conduct and during reverse biased condition(generally doring reverse biased condition ckt is open mens no current flows;when register is connected)current flows but during reverse biased condition 1--for sometimes initially current flows due to discharging of capacitor. 2--then ckt will be having no current
What is the torque converter ckt performance?
What is the torque converter ckt performance?
How do you create essential hazards?
as we know that sequential ckt = combinational ckt + feedback So if we clear the hazards of combinational ckt then also some type of disturbance left in the ckt .That disturbance is known as ESSENTIAL HAZARDS.
Why inductor are used in CKT?
inductor is used in ckt because it will work as controling current device
What is the mean of CKT?
CKT is electrician short hand for circuit. A circuit is everything powerd by on circuit breaker
Why alternator rating in KVA?
as while designing alternator we have to consider two ckt. i.e. electrical ckt.& magnetic ckt. and electrical ckt.is designing by considering current & magnetic by volt.thats why rating is in kva.
What is the advantage of parallel circuit from serios circuit?
In parallel ckt voltage in all branches will be same, its different in series ckt
Control diagrame of a capacitor bank and why you use capacitor banks?
---- Capacitor banks used to improve power factor(lagging) of a circuit:: This is necessary since it causes saving in power and electricity bill in following ways: 1) As p.f rises, circuit currnt decreases and hence I2R losses reduce 2) Var consumption reduces There is no tool provided here to draw the ckt diagram:: U take on PFC(power factor correction bus), then connect switch fuse, then HRC fuse, then Contactor, then overload relay and finally the capacitor bank
Discuss what would happen if a resistor was not inclued in a circuit?
u can't avoid resisters in ur ckt because even the components using in ur ckt hav its own resistance........ if u r not using a resistance in ur ckt u cannot vary the parameters like power voltage current etc.. such ckt is a vaste
What are the application of a differentiating amplifier?
It is a signal checking or comparing ckt..... So we can use it in the analog or digital locker ckt's or in security check's etc....
