answersLogoWhite

0

What else can I help you with?

Continue Learning about Engineering

Can inserting a resistor in a circuit have an effect similar to an short circuit?

It creates an extra load to the circuit if placed parallel to other circuits. this load approaches the equivalent of a short circuit as the resistance value placed there reduces.


Is the total resistance of all the parallel loads more than the smallest individual resistance?

No. Perhaps an analogy would help understand the answer to this question. When you are at the store, and you are in a line waiting to be paid, opening up another line or more should increase how fast people can move through the store. That is a parallel operation. (If you have to go through one line at the store and then go through another line at the store, that is a series operation). Similarly, when a current meets a resistance, putting additional resistance in PARALLEL allows some of the current to divert to this new path or paths, allowing more current to flow through the combination of resistances. Since more current is flowing though the combined resistances, the equivalent resistance is less since less resistance always means more flow.


Why does voltmeter have high internal resistance?

No, ammeters have a low internal resistance. This is so that when they are put in series with a circuit, they change the circuit's operating characteristics as little as possible.Contrast this with voltmeters, which do have a high internal resistance, and which are intended to be placed in parallel with the circuit they are measuring.Use the link below to the related question on why ammeters have a low internal resistance and read through that information to see why things are the way they are.


What is the difference between on and off state resistance?

On Circuit Resistance = Close to the total load Resistance. Off Circuit Resistance = Near Infinitive High Resistance.


How must voltmeters be connected in a circuit?

Voltmeters must be connected in parallel with the component or section of the circuit where the voltage is to be measured. This parallel connection allows the voltmeter to measure the potential difference across the component without significantly affecting the circuit's operation. It is important to ensure that the voltmeter has a high internal resistance to minimize the current flowing through it and avoid altering the circuit behavior.

Related Questions

What will happen to a buzzer connected to a circuit?

If it is connected in series with a circuit then it might raise the resistance too high and fail the system. Parallel connection is a circuit is probably the best bet you have.


Can inserting a resistor in a circuit have an effect similar to an short circuit?

It creates an extra load to the circuit if placed parallel to other circuits. this load approaches the equivalent of a short circuit as the resistance value placed there reduces.


Is the total resistance of all the parallel loads more than the smallest individual resistance?

No. Perhaps an analogy would help understand the answer to this question. When you are at the store, and you are in a line waiting to be paid, opening up another line or more should increase how fast people can move through the store. That is a parallel operation. (If you have to go through one line at the store and then go through another line at the store, that is a series operation). Similarly, when a current meets a resistance, putting additional resistance in PARALLEL allows some of the current to divert to this new path or paths, allowing more current to flow through the combination of resistances. Since more current is flowing though the combined resistances, the equivalent resistance is less since less resistance always means more flow.


What happens to the resistance in a parallel circuit when more light bulb is added?

When more light bulbs are added to a parallel circuit, the total resistance decreases because each additional bulb provides an additional pathway for current to flow. This results in an increase in the overall current flowing through the circuit, as well as an increase in the total power consumed by the circuit.


When is too high a resistance not a good thing in a circuit?

Too high a resistance is always not a good thing in a circuit. That's what "too high" means.


Why does voltmeter have high internal resistance?

No, ammeters have a low internal resistance. This is so that when they are put in series with a circuit, they change the circuit's operating characteristics as little as possible.Contrast this with voltmeters, which do have a high internal resistance, and which are intended to be placed in parallel with the circuit they are measuring.Use the link below to the related question on why ammeters have a low internal resistance and read through that information to see why things are the way they are.


What is the difference between on and off state resistance?

On Circuit Resistance = Close to the total load Resistance. Off Circuit Resistance = Near Infinitive High Resistance.


How does the loading effect of an ammeter in a low resistance circuit compare to the loading effect in a high resistance circuit?

The voltmeter has an internal resistance, which should be as high as possible. As this resistance draws current from the circuit under test, it will affect circuit operation. This is more pronounced in a high impedance circuit because the current drawn flows through higher resistances.


Why is parallel resonant circuit called a rejector circuit?

because at resonance frequency in LRC parallel circuit,impedance is high, so it minimize the current. thus we say its a rejector circuit .


An open circuit has an infinate resistance?

There is no such a thing as infinite resistance but it could be a very high resistance.


How must voltmeters be connected in a circuit?

Voltmeters must be connected in parallel with the component or section of the circuit where the voltage is to be measured. This parallel connection allows the voltmeter to measure the potential difference across the component without significantly affecting the circuit's operation. It is important to ensure that the voltmeter has a high internal resistance to minimize the current flowing through it and avoid altering the circuit behavior.


How parallel resistors work?

Resistors in parallel work just like highway lanes in parallel. -- The more lanes there are, the more traffic they can carry. -- Any number of lanes in parallel are always wider than the widest single lane, and can carry more traffic than the widest single lane can. "wide lane" = low resistance "narrow lane" = "high resistance" "traffic" = "electric current"