answersLogoWhite

0

Line current = 1.732 x Phase Current

Comment

Only for balanced loads.

User Avatar

Wiki User

12y ago

What else can I help you with?

Continue Learning about Engineering

When is a motor in star or delta connection?

Star (or wye) connection is where each of the three phases has a fourth conductor, neutral, as its current return. Current flow in this configuration is phase to neutral, which is also grounded back at the distribution center. There will be five total connections, phase A, B, and C, neutral, and (protective earth) ground. Delta connection is where each of the three phases uses the prior phase as its current return. Current flow in this configuration is phase to phase, and there is no neutral, though there is still a ground. There will be four total connections, phase A, B, and C, and (protective earth) ground.


What is the difference between an open delta and an open wye connection?

An open delta connection is a delta connection with one phase removed, but still supplied with three line conductors. An open wye is a wye connection with one phase removed, supplying a three line conductors and a neutral conductor. An open-delta/open-wye is a method of providing a reduced-load three-phase supply using just two single-phase transformers, rather than the preferred method of using three single-phase transformers.


How do you get two different voltages using the delta - star connection?

A star connection is where the three phase nonpolarities are tied to a single point, and very often grounded. A delta connection is where the nonpolarity of one phase is tied to the polarity of another phase, forming a greek delta shape. If measuring from polarity to nonpolarity on a single phase, in the star formation you are looking at L-N voltages; in the delta connection, you are looking at L-L voltages (L-N voltages * square root of three).


What is 1.73 in load current calculation?

1.73 (the square-root of 3) is the ratio of line voltage to phase voltage in a star (wye) three-phase connection, and is the ratio of line to phase current ratio in a delta three-phase connection supplying a balanced load. In each case, it is derived from the phasor addition of two values displaced from each other by 120 electrical degrees.


How can you terminate a 3 wire wye motor to a 3 phase delta connection?

To terminate a 3 wire wye motor to a 3 phase delta connection you need a 3 phase transformer to convert from delta to wye. Do not lift the common neutral connections inside the motor and rewire for delta, because the voltages will be wrong.

Related Questions

What is the connection of normal wire star or delta?

normally delta connection wired in 3 phase induction motor. during starting wiring is in Star and after running normal speed changeover to delta .beacause starting time its phase voltage equals less root3 times of line voltage ,line current and phase current equals. in Delta phase voltage and line voltage equals, and phase current equals root3 times line current


What is the formula use for calculation voltage and current in star and delta?

Balanced Star (Wye) Connected Systems:Line Voltage = 1.732 x Phase VoltageLine Current = Phase CurrentBalanced Delta Connected Systems:Line Voltage = Phase VoltageLine Current = 1.732 x Phase Current


When is a motor in star or delta connection?

Star (or wye) connection is where each of the three phases has a fourth conductor, neutral, as its current return. Current flow in this configuration is phase to neutral, which is also grounded back at the distribution center. There will be five total connections, phase A, B, and C, neutral, and (protective earth) ground. Delta connection is where each of the three phases uses the prior phase as its current return. Current flow in this configuration is phase to phase, and there is no neutral, though there is still a ground. There will be four total connections, phase A, B, and C, and (protective earth) ground.


What is the star delta working principle?

when starting a 3 phase induction motor,first start with star connection,because reduced current is being applied and after start change it to delta connection then. full line current is applied to the motor.


What happens when a phase gets short and also when it get opened in a delta and star connection?

In star connection when two phase is short,it work as single phase system. In delta when one phase is open ,it work as a single phase.


Why line current is greater than phase current in delta connection?

Because if you apply Kirchhoff's Current Law to the junction between the line current and the two phase currents, the line current is the phasor (vector) sum of two phase currents. For a balanced load (only), this works out to 1.732 x phase current.


Why does delta connection have no neutral connection?

Lets compare between a star and delta connection in 3-phase power types. In a star connection, there are 6 connections (A1, B1 and C1 being the outer arms of the 3 armed star and at the centre, A2, B2 and C2). The center is called the neutral or star point which carries out the any unbalanced current loads through its connection. That is why if you lose out the neutral point in a star connection, there will be an overflow of current through to the loads. The loads also take in more current, generating much more power and could damage the appliance you are using and the components the line current is connected to, since excess heat and overworking may result.In a delta connection, the connection has only 3 and on a piece of paper it is sketched as the connections being joined arm to arm. One side is A phase, B phase and C phase. Getting to the point, a Delta connection does not have a earth wire because the live voltage is always the same throughout the connection. Since phase and line voltage are the same and constants. It also means the line current will change without affecting other components within the circuit. Balanced Delta connected circuits or loads can only have their power supply sourced from a star connection and a balanced Star load can only have their voltage supply come from a delta connection.Another AnswerWith a delta connection, the phasor sum of the three line currents is zero, whether the load is balanced or unbalanced, so no neutral is necessary.


What can be done with the help of star and delta conversions?

Using star delta method of wiring you can run high rated motor with out any high starting current. Star connection can provide 3 phase power as well as single phase load


Why star connection draw low current?

In star each phase is 120 degree apart in delta angle between phases(R,Y,B) are 60 degree so star connection draw low current.


What is the difference between an open delta and an open wye connection?

An open delta connection is a delta connection with one phase removed, but still supplied with three line conductors. An open wye is a wye connection with one phase removed, supplying a three line conductors and a neutral conductor. An open-delta/open-wye is a method of providing a reduced-load three-phase supply using just two single-phase transformers, rather than the preferred method of using three single-phase transformers.


What is the current in star connection?

If a motor is connected in star, the current in the motor winding will be equivalent to the line current. If the motor is connected in delta, the current will be 1/sqrt(3) of the line current. If three phase CTs are connected in Delta, their secondary current will be sqrt(3) higher than the CT ratio implies by the line current.


How do you get two different voltages using the delta - star connection?

A star connection is where the three phase nonpolarities are tied to a single point, and very often grounded. A delta connection is where the nonpolarity of one phase is tied to the polarity of another phase, forming a greek delta shape. If measuring from polarity to nonpolarity on a single phase, in the star formation you are looking at L-N voltages; in the delta connection, you are looking at L-L voltages (L-N voltages * square root of three).