0
While I can't offer uber-technical reason, some commen sense reasons jump to mind: 1. if the device being protected shorts to ground, then a fuse on the neutral side would not blow, thus not protecting the device and wiring. 2. it's better sense to put the fuse as close to the main power as possible, like to a main breaker or meter, so that if the fuse does have to blow, more line is unenergized, decreasing the likely hood of further equipment damage or even personal injury. 3. if the fuse is on the neutral side and it blows, how do you know which device made the fuse blow? trouble shooting is more complicated as you have to test more devices. 4. with my limited understanding of multi phase power, the total current 'seen' through the neutral is often less than the current through each phase, so the device that fails could do much more damage by having to blow a fuse on the neutral side. note: reason 4 is up for debate as I'm not sure I'm correct, it's only what I have understood from some reading.
What else can I help you with?
If in the three phase connection phase to phase voltage is 400v what will be the phase neutral voltage?
The formula to use is, phase voltage /1.73 = phase to neutral (ground) voltage.CommentThere is no such thing as a 'phase to phase', or 'phase to neutral' voltage. The correct terms are 'line to line' and 'line to neutral'. So the above answer should read: line voltage/1.73= line to neutral voltage = phase voltage.
What voltage should 208 3 phase leads read?
From line-to-line (any two of the three leads) voltage or 'line voltage', the voltage is 208 V. The line-to-neutral (one of the three leads and the neutral conductor), or 'phase voltage', is 120 V.
When the neutral switch is open where do the line current flow to?
There is never a switch installed in a neutral line.
What is neutral to ground fault?
Neutral, by definition, is grounded at the distribution panel, and also at the distribution pole. That is how the hot to ground voltages are prevented from exceeding their normal voltage and encroaching on truly lethal voltages, such as 7.6kV in a typical US 13.2kV system, in a wye configuration.Note: and this is critical, do not depend on the fact that neutral is grounded and consider that it is the same as protective earth ground. It is not. Protective earth ground is a different wire.
Can you use ohm-meter to measure a resistance between the neutral line N and the ground E?
If the meter is sensitive enough and there is a resistance between the neutral and ground then the meter should be able to detect it.
What will happen if phase and neutral get reversed in power line and what action we have to take against it?
If phase and neutral get reversed in a power line, electrical appliances may malfunction, and there is a risk of electrical shock to users. To rectify this issue, you must immediately shut off the power supply and contact a qualified electrician to correct the wiring configuration. Reversing phase and neutral can be dangerous and should be addressed promptly to prevent any potential hazards.
If in the three phase connection phase to phase voltage is 400v what will be the phase neutral voltage?
The formula to use is, phase voltage /1.73 = phase to neutral (ground) voltage.CommentThere is no such thing as a 'phase to phase', or 'phase to neutral' voltage. The correct terms are 'line to line' and 'line to neutral'. So the above answer should read: line voltage/1.73= line to neutral voltage = phase voltage.
What voltage should 208 3 phase leads read?
From line-to-line (any two of the three leads) voltage or 'line voltage', the voltage is 208 V. The line-to-neutral (one of the three leads and the neutral conductor), or 'phase voltage', is 120 V.
Why no electric shock from neutral line?
There is normally no voltage on the neutral line because the neutral line is grounded. However, and this is always important, do not assume that neutral is grounded, nor that there is not an elevated voltage on neutral or ground due to a possible ground fault.
When the neutral switch is open where do the line current flow to?
There is never a switch installed in a neutral line.
Is the blue line a part of the neutral zone?
The blue line is what separates the neutral zone from a team's offensive and defensive zones.
Is it possible to connect 3 phase 440 V without neutral line to the machine having 3 phase 4 wires with neutral line?
No, it is not possible to connect a 3-phase 440 V system without a neutral line to a machine that requires a 3-phase 4-wire connection with a neutral line. The neutral line must be present in both systems for proper operation and safety. Trying to connect them without the neutral line could cause damage to the machine and pose a safety hazard.
What is neutral to ground fault?
Neutral, by definition, is grounded at the distribution panel, and also at the distribution pole. That is how the hot to ground voltages are prevented from exceeding their normal voltage and encroaching on truly lethal voltages, such as 7.6kV in a typical US 13.2kV system, in a wye configuration.Note: and this is critical, do not depend on the fact that neutral is grounded and consider that it is the same as protective earth ground. It is not. Protective earth ground is a different wire.
Un-fused multiple outlet extension cords should?
should not be used
Does my car's heater has a fuse?
The car heater is a vague question. The heater core is not fused, it is like a mini radiator. The blower motor for heat/AC is fused. The selector blower motor resistor is fused in line with blower motor. Now if you lost heat, the water pump is belt driven, not fused.
Can you use ohm-meter to measure a resistance between the neutral line N and the ground E?
If the meter is sensitive enough and there is a resistance between the neutral and ground then the meter should be able to detect it.
Is the AC wide prong for hot or neutral?
The AC wide prong is the neutral. An AC voltmeter measuring from narrow prong to ground should show line voltage; measurement from wide prong to ground should show zero. In a two-conductor power cord (and some three-conductor cords), the ridged side should be the neutral. In any light-bulb socket, the outer ridge should be wired to neutral.
