answersLogoWhite

0

Depends on the motor. If it is a synchronous motor it will run too fast.

User Avatar

Wiki User

13y ago

What else can I help you with?

Continue Learning about Engineering

Can I run laundry equipment 440V 60hz 3 pH on a 480V 60Hz system?

This should not be a problem but check with the manufacturer of the laundry equipment to be certain.


What is the minimum acceptable reading for magger test for 480v motor?

if check voltage is 2000v then acceptable range is 400


Is there any advantage of 208V vs 480V three phase?

208 v. equipment is a little smaller and cheaper, and 208v. is slightly safer to use. However, 480v. runs on half the amperage 208v. equipment does, which means equipment or devices cost almost 50% less to operate. With respect to energy consumption, the answer above is incorrect. It is true that equipment that operates at 480v does operate at roughly half the amperage vs. 208v, however, it operates at over twice the voltage. Your local power company charges you per kilowatt hour (voltage x amperage), not on amperage alone. Example, a 208v motor that draws 10 amps would consume (208v x 10a) 2.080 kilowatts per hour. The same motor on 480v would draw roughly half, 4.3 amps (480v x 4.3a) and would also consume 2.080 kilowatts per hour. So in terms of power consumption, they are virtually the same. The main reasons one would opt for higher is the fact that you can install smaller wire and you can run longer distances. It's a ratio that is directly proportional (at least with electric motors/inductive loads). If you were comparing a 240v motor to a 480v motor the ratio would be exact, if a 480v motor draws 5 amps, the same motor on 240v would draw 10 amps.


Can a 440 - 480V 60Hz motor run in a site with 380V 60Hz supply If No how can it work?

The motor will run, probably at nearly the same speed, but it cannot supply the same mechanical load. If it can be run on a lighter load, proportional to the voltage, it should be OK.


What is the acceptable voltage higher than 480v for a 480v inverter?

The voltage range should be marked on the case but without that information a 5% increase can be assumed, so 504 v.

Related Questions

What happen to the 480v rated motoe when connected to 440v power?

Depending on the design of the motor, it may just run with less torque/hp. It might run slightly hotter as well, depending on the load.


Can I run laundry equipment 440V 60hz 3 pH on a 480V 60Hz system?

This should not be a problem but check with the manufacturer of the laundry equipment to be certain.


Can you run a 460v 60hz motor to a 480v supply?

The the supply stays within +/- 5% of what the motor is rated for, you can do this.


What is the minimum acceptable reading for magger test for 480v motor?

if check voltage is 2000v then acceptable range is 400


3 phase reverse relay can be utilized for motor control speed?

3 phase reverse relay can be utilized to control 480V motor 60HZ for controlling their speedspeed.


Power a 415volt motor with 480volts?

in low voltage connection in wye (star conncetion) 415v high voltage connection in delta 480v


What is full load current of 20 HP induction motor in delta?

480V about 20A 240V about 40A look at the nameplate duty cycle and efficiencies vary


How many watts are in 650mA?

not enuff information 20 leds in parallel at 2.5v about 2W a motor at 480V 3 phase 600 w or 3/4 hp


How many kw in 480v?

To calculate the kilowatts (kW) when given voltage (V) and current (I), you can use the formula: kW = V x I x √3 / 1000 For 480V, the calculation would be based on the current flowing through the circuit.


Is there any advantage of 208V vs 480V three phase?

208 v. equipment is a little smaller and cheaper, and 208v. is slightly safer to use. However, 480v. runs on half the amperage 208v. equipment does, which means equipment or devices cost almost 50% less to operate. With respect to energy consumption, the answer above is incorrect. It is true that equipment that operates at 480v does operate at roughly half the amperage vs. 208v, however, it operates at over twice the voltage. Your local power company charges you per kilowatt hour (voltage x amperage), not on amperage alone. Example, a 208v motor that draws 10 amps would consume (208v x 10a) 2.080 kilowatts per hour. The same motor on 480v would draw roughly half, 4.3 amps (480v x 4.3a) and would also consume 2.080 kilowatts per hour. So in terms of power consumption, they are virtually the same. The main reasons one would opt for higher is the fact that you can install smaller wire and you can run longer distances. It's a ratio that is directly proportional (at least with electric motors/inductive loads). If you were comparing a 240v motor to a 480v motor the ratio would be exact, if a 480v motor draws 5 amps, the same motor on 240v would draw 10 amps.


Can a 440 - 480V 60Hz motor run in a site with 380V 60Hz supply If No how can it work?

The motor will run, probably at nearly the same speed, but it cannot supply the same mechanical load. If it can be run on a lighter load, proportional to the voltage, it should be OK.


Can you feed a 208v 200amp panel from 480v 20amp circuit?

Not directly, you would need to transform 480v circuit to 120v with a transformer first.