0
Need to replace diaphragm an piston under large chrome cap on top. Repair kit can be purchased at most any Plumbing supply house, you will need to tell them if it is for a urinal or a water closet . Be sure to turn off water supply before repairing, screwdriver stop slot located under small cap on right or left of main valve
What else can I help you with?
How can you manualy open the zone valve for more heat?
If it is already open than you wont get more heat. If you have a normally closed type than there is a valve lever on one side that can be slide over and locked into place.
York furnace pilot light is on replaced thermo stat and thermo couple still wont come on?
Bad thermo,replace. The thermo senses that the pilot is lit and opens gas valve,also could be bad or blocked gas valve.
How can you determine if you need a new valve or just a trim kit to change a tub and shower faucet when staying with the same set up?
A trim kit is just the outside parts that you see. This will make you faucet look better, but it wont affect the function of your old valve. If your shower valve doesn't work right, replace it.
Why does my technics hifi cut off?
Inside the amplifier on the main PCB (Printed circuit board) there are 2 speaker protection/power relays. When they become old and worn the contacts inside become less conductive (worn out) and they dont always make a good contact, when this happens the hi fi wont turn on. It will eventually stop powering up and it wont work. The remedy is to replace both the relays, de solder them and solder in new ones, problem is you probably wont be able to source the parts.
Will a motor shut down if the run capacitor fails?
If a motor is running when the cap fails it will probably continue to run at much higher amp draw and most likely shut down on thermal overload. It can start with a bad cap, but in my experience it most likey wont.
Why wont your 88 crx hf stay running?
maybe the fast idle valve. mine started to die whenever i had that lowered.
Dodge durango abs motor wont stop running killing your battery?
Change the abs motor.
Fuel flow wont stop on carbits a mikunni carb on a golf cart?
Bad needle/seat valve in carb.
Why is fan on your 2004 Pontiac GTO wont stop running?
fan control relay is bad, contacts are fused together
98 blazer starts but wont stay running?
my guess woul be that your EGR valve is bad or is sticking i would pull it out and check its the thing under the inlet of your intake if its good then the valve on it will move back and forth easy if its bad then it will stick
You just had a valve job done on your 2002 kia optima drove it home fine and now car wont turn over wants to start by wont stay running any idea what it is Fuel pump was replaced as well?
Call the person who repaired the car and tell them what is going on. But what you write above makes no sense. You say, "(wont turn over) (wants to start) by (wont stay running)" If it won't turn over, how does it want to start, and how can it be running in the first place? Did they replace the fuel filter. If not, they should have.
What happens if you put a PCV valve in backwards?
pcv valve wont work properly
Why wont supply valve for toilet shut off after valve is closed?
It needs a new washer in it.
Why did my 1988 supra stop running and wont crank back not getting fire to the spark plugs?
Check your ignitor and the coil. They are located one on top of the other.
Antifreeze wont stop running out of overflow when motor warms up causing it to overheat?
start by replacing rad. cap. if that doesnt help you have a blown headgasket.
How do you know if a have a bent mechanism on my trumpet?
If you have a bent valve slide, or valve, or valve casing, they usually wont move. Valve's and valve casings would prevent the valves from moving, while bent valve slides wont easily pull out. If you suspect a bent valve, valve casing, or slide, try cleaning and oiling it first, valves and slides can become stuck with the lack of valve oil or slide grease.
What happens if you turn on your X-box 360 and the game character wont stop running?
it could just be your controller. try messing around with the analogs or a new controller.
