0
What else can I help you with?
When using an antenna to measure leakage the antenna must be elevated from leakage source and ground.?
When measuring leakage with an antenna, it is essential to elevate the antenna above both the leakage source and the ground to ensure accurate readings. Elevation minimizes the effects of ground reflections and interference, allowing for a clearer detection of the leakage signal. Additionally, being elevated helps reduce the influence of nearby structures and obstacles that could distort the measurement. This positioning ensures that the antenna captures the true electromagnetic field generated by the leakage source.
Is antenna passive or active component?
An active antenna is an antenna which has an amplifier attached very closely to it. The antenna/amplifier system is called an active antenna. It is used for receiving signals only. The idea is to set the signal-to-noise ratio (SNR) before the signal travels along a transmission line where it is susceptible to interference and loss.
Can you replace an XM radio antenna with any other antenna like a 3ft hard cb antenna?
You can replace an XM radio antenna with a CB antenna, a ham 40-meter mobile antenna, a cellphone antenna, a GPS antenna, a TV antenna, a wire coat hanger, a 6 GHz microwave antenna, or a chain of paperclips. However, since none of them is optimized to operate at the frequencies of XM radio, like the XM antenna is, none of the others will work as well. Most of them will likely be so inefficient at the satellite radio frequencies that when you use one of those, you hear nothing at all on your radio.
What is a reconfigurable antenna?
an antenna that is able to be formed, or bent
What is microstrip patch array antenna?
microstip patch array antenna is basically ,thecollection of antenna that give the double directive gain
What is detection antenna housing?
Harem
Chevy Caprice power antenna replace?
In my 89 you need to remove the wheel and the inside wheel housing, to get full access to the antenna.
How do you change the antenna base on a Ford Focus?
how can i change the antenna base on ford focus its broken Remove the maplight cover and bulb housing. There is a single screw that secures the antenna base.
How do you replace an electric antenna on a 89 caprice classic?
In my 89 you need to remove the wheel and the inside wheel housing, to get full access to the antenna.
How do you replace power antenna on 1992 corvette?
Remove left rear wheel plastic housing cover under the body you can then access the antenna motor.
How do you troubleshoot wifi antenna problems?
You can go to this website called, driverwhiz.com and they will fix any wifi problems you are currently having with bad signal detection. This website is simple and easy to use and definitely worth it.
How do you replace the antenna on a Ford Focus?
To replace the antenna on a Ford Focus remove the antenna from the base using a screwdriver. Remove the lighting assembly hose with a small key. Remove the plug in wires and the plastic housing. Put the new antenna base in place than screw in the new antenna.
Where is the antenna on a 1999 Honda Civic?
The antenna on a 99 civic is normally located on the roof next to the drivers side door on the roof. There should be a black casing right above the windshield and the antenna should be right there, if there is a casing and no antenna then someone has pulled it out and you will have to replace the entire antenna housing. Hope this helps.
How do you replace automatic antenna on a 1990 Toyota Celica?
First, you must go into the trunk of the car and remove the left side panel beside the antenna. this chould expose the antenna motor and electrical housing. Disconnect the 2 plugs and remove the antenna. Instalation is the same but in reverse ;) <3
What is a Spherical antenna protector called?
It is called RADOMES
What are senses organs called?
antenna
How do you replace the electric antenna mast on a 1990 Honda Accord EX?
Remove the nut, spacer and bushing that holds down the antenna on the outside car body. Then turn the radio ON. As the antenna extends out, carefully pull out the antenna mast. There will be a plastic portion with teeth at the end. Remember the direction of teeth. When you install the new antenna, the teeth will go in that direction. Insert the new antenna into the antenna housing. Make sure the antenna teeth engages the antenna motor by moving the antenna up & down. Turn the radio OFF and the antenna motor will pull the antenna back in. Reinstall the nut, spacer, bushing and you're done.
