answersLogoWhite

0

The phase shift in three-phase transformer from winding of Transformer and determine by vectorgroup of transformer such as YNd1 High voltage connect to wye Low Voltage connect to delta so L.V. lag H.V 30 degree.

Answer

'Phase shift' or, more accurately, 'angular displacement', is the angle between the secondary line voltages and primary line voltages of a three-phase transformer.

User Avatar

Wiki User

12y ago

What else can I help you with?

Continue Learning about Engineering

Why vector group is required?

There are various ways in which you can connect a three-phase transformer's primary and secondary windings, or in which you can connect three single-phase transformers to create a three-phase transformer bank. For example: wye-wye, wye-delta, delta-delta, delta-wye, etc.For each connection, there is a natural phase shift between the primary and secondary line voltages. This is called the angular displacement (or 'phase displacement') of the transformer connection.If you wish to parallel two three-phase transformers, or two three-phase transformer banks, then their angular displacements must be the same (there are also other requirements not relevant to this answer).A vector group is a method of specifying a three-phase transformer (or transformer bank) method of connection and its angular displacement. Transformer connections from the same group can be paralleled. Those in different groups cannot


What is the current of 1MVA transformer?

This depends on the voltage, and whether it is a three phase or single phase transformer.


Would you install three-phase transformer or bank of three single phase transformer in a large power station and justify by comparing the two schemes?

A three-phase transformer bank is often used in power stations because it is easier to construct and transport very large single-phase transformers, compared with constructing and transforming an equivalent-capacity three-phase transformer.


Can 3 single phase transformers can replace 1 three phase transformer?

Yes, you can use three single phase transformers on three phase applications and interconnect them to serve as a single transformer or you could use one single phase transformer fed from two of the three lines in a step down application.


What will happen if apply two phase supply to a three phase transformer?

A three phase transformer is simply three transformers so, supplying one phase to a set of three transformers will result in only one phase output. Any loads connected to that transformer that are expecting three phase power will malfunction, and could fail.AnswerA three-phase transformer is NOT 'three separate single-phase transformers', as suggested in the original answer. It is a single transformer with three primary and secondary phase-windings wound around a common three-limb ('core') or five-limb ('shell') core. If a single-phase supply was applied to one of the three primary windings, then single phase voltages would appear across each of the three secondary windings and the remaining two primary windings. These voltages would not be out of phase with each other.

Related Questions

Why vector group is required?

There are various ways in which you can connect a three-phase transformer's primary and secondary windings, or in which you can connect three single-phase transformers to create a three-phase transformer bank. For example: wye-wye, wye-delta, delta-delta, delta-wye, etc.For each connection, there is a natural phase shift between the primary and secondary line voltages. This is called the angular displacement (or 'phase displacement') of the transformer connection.If you wish to parallel two three-phase transformers, or two three-phase transformer banks, then their angular displacements must be the same (there are also other requirements not relevant to this answer).A vector group is a method of specifying a three-phase transformer (or transformer bank) method of connection and its angular displacement. Transformer connections from the same group can be paralleled. Those in different groups cannot


What is the current of 1MVA transformer?

This depends on the voltage, and whether it is a three phase or single phase transformer.


What is the voltage phase shift between primary and secondary line voltages in star-delta transformer connection?

The voltage phase shift between primary and secondary connections in a transformer is 180 electrical degrees.


What is this system called with three single phase transformer?

Your question is rather vague. If you are asking what do you call a group of single-phase transformers, connected to supply three phase, then the answer is a 'three-phase transformer bank'.


Would you install three-phase transformer or bank of three single phase transformer in a large power station and justify by comparing the two schemes?

A three-phase transformer bank is often used in power stations because it is easier to construct and transport very large single-phase transformers, compared with constructing and transforming an equivalent-capacity three-phase transformer.


Is there a basic difference between a three phase power transformer and a three phase distribution transformer?

The basic difference is the secondary voltages. On a distribution transformer the secondary voltage is very high. This is to overcome line loss for transmission of electricity over long distances. A three phase power transformer is used at the consumers three phase services end to manipulate voltages that consumers need to operate their equipment. The transformer that feeds your house is considered to be a single phase power transformer.


Can 3 single phase transformers can replace 1 three phase transformer?

Yes, you can use three single phase transformers on three phase applications and interconnect them to serve as a single transformer or you could use one single phase transformer fed from two of the three lines in a step down application.


What will happen if apply two phase supply to a three phase transformer?

A three phase transformer is simply three transformers so, supplying one phase to a set of three transformers will result in only one phase output. Any loads connected to that transformer that are expecting three phase power will malfunction, and could fail.AnswerA three-phase transformer is NOT 'three separate single-phase transformers', as suggested in the original answer. It is a single transformer with three primary and secondary phase-windings wound around a common three-limb ('core') or five-limb ('shell') core. If a single-phase supply was applied to one of the three primary windings, then single phase voltages would appear across each of the three secondary windings and the remaining two primary windings. These voltages would not be out of phase with each other.


Where are three phase transformer systems used?

Any where that a three phase supply distribution is needed to operate three phase equipment.


Why would you use a three phase transformer in place of a single phase transformer?

the necesscity of two three phase transformers operating in parallel are as follows...if the one transformer fails to give supply,then another transformer can be used in parallel and hance,continuity of supply can be maintained.one transformer can be easily take out from the supply for repair & maintanance.if the load on the substation increases beyond the rated values of transformer, then another transformer can be used to share rhe load of the substation.


How do you design a transformer with three phase 400v input and single phase 2000v output?

By design are you going to wind the transformer yourself? In your design you need a 5:1 ratio. On the output side of the transformer any two legs of a three phase transformer is considered single phase voltage. Good luck on your project.


What is the three phase transformer?

it has three primary windings & three secondary windings.