0
What else can I help you with?
How much load for 50mm2 cable?
There's no such word as "'Ampacity". The current carrying capacity of 50mm cable is around 300A continuous or 365amps @ 60% duty cycle. It's generally used for engine starter circuits or high current welders.Answer'Ampacity' is a North American term for the 'current-carrying capacity' of a cable. It is not used in most other English-speaking countries.
Would 10mm sq cable suit an 18kw 3 phase 415 volt motor over 25mt length?
The motor would draw about 24 kVA which is 35 amps. For this you would need 10 mm2 cable.
What is the adjustment factor for a raceway or cable that has 7-9 current carrying conductors?
The adjustment factor for a raceway or cable with 7-9 current-carrying conductors is typically 70%. This means that the ampacity of each conductor must be reduced to 70% of its rated value to prevent overheating and ensure safe operation. This adjustment is necessary to account for the increased heat generated when multiple conductors are bundled together. Always refer to the National Electrical Code (NEC) for the most accurate and applicable guidelines.
How many current carrying conductors can you have in a conduit before you have to start derating amparage?
The number of current-carrying conductors allowed in a conduit before derating is specified by the National Electrical Code (NEC). Generally, if you have more than three conductors in a conduit, you need to start derating the ampacity of the conductors. Specifically, for more than three conductors, the ampacity of each conductor must be reduced based on the number of conductors present. For example, with 4 to 6 conductors, the ampacity is typically reduced to 80%, and with 7 to 9 conductors, it’s reduced to 70%.
What is 10 french tubing?
It is a medical tube that 10mm in diameter.
What is the ampacity of a NM-B cable?
Allowable ampacity for 10-2 copper NM-B is 30 A.http://www.cerrowire.com/default.aspx?id=46
Is 10mm cable safe for 50a breaker?
No, a 10mm cable should be used with no more than a 40A breaker for typical household wiring. Using a 10mm cable with a 50A breaker can lead to overheating and pose a fire hazard. It's important to follow the proper cable size guidelines to ensure safety.
What is the ampacity of 70mm cable?
Capacity for cable 70mm (143-212 amp) and may vary depending on installation method used.
What is the ampacity of a 10-2 NM-B cable?
Allowable ampacity for 10-2 copper NM-B is 30 A.http://www.cerrowire.com/default.aspx?id=46
What is the ampacity of 8 awg cable?
The ampacity of 8 AWG copper wire is typically around 40 to 55 amps, depending on factors such as insulation type, installation conditions, and ambient temperature. For aluminum wire of the same gauge, the ampacity is lower, approximately 30 to 40 amps. Always consult the National Electrical Code (NEC) or local regulations for specific applications and conditions.
What is Wire ampacity?
It is a North American electrical term. It is a combination the words amp and capacity rolled into one word "ampacity". When talking about how much amperage a wire can legally draw, it is referred to as the wire's "ampacity".
How do you calculate the requirement of cable size for a given load?
If you know the size of the load to be served, multiply it by 125% ( times 1.25) and choose a conductor that is rated for that ampacity or higher.
How many amps 95mm cable could take?
The maximum current that a 95mm cable can take would depend on the specific type or rating of the cable. Typically, a 95mm cable can handle currents ranging from 300 to 400 amps. It's important to consult the manufacturer's specifications or a qualified electrician to determine the exact ampacity rating for the specific cable in use.
Can you use aluminum service cable to feed a sub panel?
Yes, as long as it has the necessary ampacity for the load and is properly fastened at each terminal. For example, we have a 4/0 aluminum cable feeding our 200 A subpanel 120 feet away.
How much load for 50mm2 cable?
There's no such word as "'Ampacity". The current carrying capacity of 50mm cable is around 300A continuous or 365amps @ 60% duty cycle. It's generally used for engine starter circuits or high current welders.Answer'Ampacity' is a North American term for the 'current-carrying capacity' of a cable. It is not used in most other English-speaking countries.
What determines the ampacity of wire?
Conductors must have an ampacity not less than the maximum load that they are supplying.
What determine the ampacity of a wire?
Conductors must have an ampacity not less than the maximum load that they are supplying.
