An On-Load Tap Changer (OLTC) is a device used in Transformers to automatically adjust the voltage levels while the transformer is in operation. Its primary function is to regulate the output voltage to maintain it within desired limits despite variations in load or input voltage. By changing the transformer’s tap settings under load, the OLTC ensures efficient power distribution and enhances the stability of the power system. This capability helps to minimize voltage fluctuations and improve overall system reliability.
oltc is situated on primary side of transformer because by primary side we can obtain fine voltage change by tapping with low current flow through it.
OSR meance oil surge relay & it is used in x'mer OLTC . it is measured if any surge produce in oil then the give the signsl to relay panel for tripping of transformer
It is called callback function. For an example see the qsort function.
A function is not deigned in to another function. It is because that would lead to dependency injection.
yes, we can not declare a function in the body of another function. but if we declare a function in the body of another function then we can call that very function only in that particular function in which it is declared; and that declared function is not known to other functions present in your programme. So if a function is required in almost all functions of your programme so you must declare it outside the main function i.e in the beginning of your programme.
If the OLTC is on the secondary, and the secondary voltage is high, the OLTC will tap down, which will lower the voltage. Typical range of OLTC is +/- 10%. The primary may also have multiple taps so the OLTC can be set at '0' under normal conditions.
oltc is situated on primary side of transformer because by primary side we can obtain fine voltage change by tapping with low current flow through it.
OCTC means off circuit tap changer (off load tap changer) and OLTC means on load tap changer. in octc we can change the tap position while the transformer is in off condition only. we can not change the tap position of octc in charged condtion of the transformer. the tap position of octc can be change in deenrgise condion of transformer only means if you nwant to chang the tap position firstly you will have to deenrgise the power transformer then you can change the tap position of octc.while in oltc we can change the tap position of OLTC in charged condition of power transformer. This is the basic diffirence between OCTC and OLTC.generally the OCTC used in single phase generating transformer (G.T.Power Transformer) and OLTC used in three phase powwer transformers like standby transformer and auto transformer in power plants and switch yards. for any other question please mail me at (ashu_uit2007@yahoo.co.in )
It means 'on-load tap changer' - I found a page in Wikipedia that explains it - see related link. Read the section titled 'Voltage considerations'
OSR meance oil surge relay & it is used in x'mer OLTC . it is measured if any surge produce in oil then the give the signsl to relay panel for tripping of transformer
The TRANSFORMER PROTECTOR is a transformerexplosion and fire prevention system suitable for any type of oil-immersed transformer and including surrounding equipment such as the On Load Tap Changer (OLTC), Oil Cable Box (OCB), and Oil Bushing Cable Box (OBCB).
RTCC (Remote tap changer control) panel is one of the LT panel which has microcontroller, contactors, relays etc it senses the fluctuation in distribution voltage (input of Transformer) & give signal to OLTC to change the voltage(Output of the transformer) to set a value
OLTC - INSTALLED IN THE PRIMARY SIDE OF A POWER TRANSFORMER TO SELECT OR ADJUST VOLTAGE. THE ADVANTAGE OF THIS IS FOR SOLVING THE VOLTAGE DROP ISSUES IN THE SECONDARY OUTPUT IN THE FARTHEST LOCATION. FOR EXAMPLE YOUR SECONDARY VOLTAGE REQUIREMENT IS 380 VOLTS AND YOU CAN ADJUST TO 400 VOLTS FOR LONG CABLE RUNS.
Function
For carrying Short Circuit Test on Power Transformer Do the following: 1] Isolate the Power Transformer from service. 2] Remove HV/LV Jumps and Disconnect Neutral from Earth/Ground. 3] Short LV Phases by Cu/Al plate which could withstand short circuit current and connect these short circuited terminals to Neutral 4] Energise HV side by LV supply (440 3ph Supply) with OLTC tap position on Normal. 5] Measure Current in Neutral, LV line voltages, HV Volatage and HV Line Currents on various OLTC Tap position. Analysis: If Neutral current is near to zero transformer windings are OK If Neutral current is higher or equal to Line current between LV Phase one of the winding is Open.
The parent function of the exponential function is ax
Such a function does not exist for English. A function call BAHTTEXT will do it for the Thai language.Such a function does not exist for English. A function call BAHTTEXT will do it for the Thai language.Such a function does not exist for English. A function call BAHTTEXT will do it for the Thai language.Such a function does not exist for English. A function call BAHTTEXT will do it for the Thai language.Such a function does not exist for English. A function call BAHTTEXT will do it for the Thai language.Such a function does not exist for English. A function call BAHTTEXT will do it for the Thai language.Such a function does not exist for English. A function call BAHTTEXT will do it for the Thai language.Such a function does not exist for English. A function call BAHTTEXT will do it for the Thai language.Such a function does not exist for English. A function call BAHTTEXT will do it for the Thai language.Such a function does not exist for English. A function call BAHTTEXT will do it for the Thai language.Such a function does not exist for English. A function call BAHTTEXT will do it for the Thai language.