answersLogoWhite

0

What else can I help you with?

Continue Learning about Engineering

What are typical values of input impedance and outoput impedance of ce amplifiers?

Output of the power amplifier is smaller 0.1 ohms and input of the loudspeaker is more than 4 ohms.


How do you measure speaker impedance?

The real impedance is the resistance in ohms more 20%. A coil resistance of 6,7 ohms X 1.20 = an impedance of 8.04 ohms. If the voice-coil had exactly 8 ohms, the impedance would be 9.6 ohms and the sound would be unclear, tending to more basses.


What does 4 ohms mean?

It means that the loudspeaker maker tells you that his loudspeaker builds an input impedance (load impedance) of Zload = 4 to 8 ohms. In audio we use always voltage matching and so the amplifier output should have a source impedance of smaller Zsource = 0.1 ohm. Scroll down to related links and look for "Damping Factor".


What does speaker A minimum 4 ohms speaker impedance means?

The speaker you connect to those terminals needs to be 4 ohms or greater.


How do you make an impedance- and level-matching transformer?

You'll need to decide *which* one you want. An impedance-matching transformer has a defined primary-to-secondary turns ratio. This *may* give the level match that you want, it may not. Alternately, you can design for a level match, which also *may* give the impedance ratio you want, it may not. It also has a defined turns ratio, but this may not meet an impedance-matching requirement. For impedance matching find the ratio of impedances, take its square root, and use that as the turns ratio: 2400 ohms to 600 ohms has an impedance ratio of 4:1, so its turns ratio will be (sqrt4) = 2:1. To level-shift 1.23 volts (+4 dB) to 300 mV (-10 dB), the ratio is (1.23/0.3) approx 4:1. From the above, you could match 2400 ohms to 600 ohms, but *not* +4 dB to -10 dB with the one transformer.

Related Questions

What is the recommended conduit size for 4/0 aluminum wire?

The recommended conduit size for 4/0 aluminum wire is 2 inches.


How many amps can 4 ought aluminum wire carry?

Aluminum 4/0 wire car carry 180 amps at at 75 degrees Fahrenheit or 205 amps at 90 degrees. .


If an amp runs 1000 w rms at 1ohm how do you wire a dual 4 ohm speaker to run at 1 ohm?

the impedance of a speaker is a characteristic that is has. A 4 ohm speaker will always have a 4 ohm impedance and it cannot be changed. If 2 speakers of 4 ohm impedance are wired in parallel, then the total impedance will be 2 ohms. Similarly, if you wire 4 speakers together, the total impedance will be 1 ohm. Wiring a 2 ohm speaker to an amplifier rated to drive a 1 ohm load should work without any problems but expect the total power output to be somewhat lower than with a 1 ohm load.


What size aluminum wire on 225 amp?

300 kcmil @ 75°


What are the safety considerations when using 4-4-4-4 aluminum wire for electrical installations?

When using 4-4-4-4 aluminum wire for electrical installations, it is important to consider safety precautions such as proper insulation, secure connections, and following manufacturer guidelines. Aluminum wire can be more prone to overheating and corrosion compared to copper wire, so it is crucial to use the appropriate connectors and techniques to prevent these issues. Additionally, regular inspections and maintenance are recommended to ensure the safety and efficiency of the electrical system.


What is the required wire size for 100?

A 100 amp service requires that you use AWG 4 copper wire or AWG 2 aluminum wire.


What type of wire, specifically aluminum wire, should be used for a 200 amp service?

For a 200 amp service, it is recommended to use aluminum wire that is at least 4/0 gauge in size to ensure proper conductivity and safety.


What size wire for electric cook top?

AWG # 6 copper or AWG # 4 aluminum


Can you wire a dvc 4 ohm sub woofer and a svc 8 ohm sub woofer together on a 4 ohm amp?

Sorry, but there is really no 4 ohm amplifier. We use only voltage bridging. The amplifier will have an output impedance of around 0.04 ohms. In hi-fi we have always impedance bridging. Zout


What Wire size for 225 amp commercial panel?

3/0 or250 aluminum


What is the recommended wire size for an 80 amp breaker?

The recommended wire size for an 80 amp breaker is typically 4 AWG (American Wire Gauge) for copper wire and 2 AWG for aluminum wire.


What is the recommended wire size for a 70 amp breaker?

The recommended wire size for a 70 amp breaker is typically 4 AWG (American Wire Gauge) for copper wire and 2 AWG for aluminum wire.