0
What else can I help you with?
What is the condition for zero voltage regulation of a single phase transformer?
zero volatge regulation means the terminal volatge of transformer at full load on a given power factor become equal to the rated teriminal volatge of transformer , it happens only for leading power factor in transformer
Why an ideal voltage regulation of a device has zero value?
An ideal regulator would hold the thing it is regulating (e.g. voltage, current, water pressure, motor speed) absolutely constant, or in other words with zero variation of that parameter. The quality of regulation in actual regulators however can only approach this ideal of zero variation.
How do you determine angle between primary line voltage and secondary line voltage of a 3-phase transformer?
You should look at the transformer vector diagram, or the type of transformer will tell you (something like YnD1, for example). If it's a Y/Y type transformer, the phase angle will be zero. If it is a D/D, it will be zero. If it's a Y/D, or D/Y, it could be +30, -30 (usually). I have seen a few strange cases where a Y/D was +150 degrees.
What is zero current transformer?
It is a transformer with No load attach to it.
Why are transformers helpful when using alternating current?
The transformer in the least complex manner can be depicted as a thing that means up or ventures down voltage. It is fundamentally a voltage control gadget that is utilized broadly in the conveyance and transmission of rotating flow power. Trutech Products is a leading Transformer Manufacturers In Pune
When voltage regulation will be zero it operate it?
A transformer will operate with a voltage regulation of zero when it is not supplying a load.
What is zero voltage regulation in transformers and what it means?
'Zero voltage regulation' indicates that there is no difference between its 'no-load voltage' and its 'full-load voltage' -this is only the case for an 'ideal' transformer.
What is the voltage regulation of an ideal transformer?
Ideally the voltage regulation voltage of a transformer should be zero. It means when you change the load from no load to short circuit (theoretically, normally you don't want to burn the transformer windings) the output voltage doesn't change and remains equal to the no load voltage.
What is the condition for zero voltage regulation of a single phase transformer?
zero volatge regulation means the terminal volatge of transformer at full load on a given power factor become equal to the rated teriminal volatge of transformer , it happens only for leading power factor in transformer
When will transformer voltage be zero?
A transformer output voltage will be zero when A. The input voltage is zero. B. When the primary (input) wire winding inside the transformer is broken, cut, or burnt out. C. When the secondary (output) wire winding is broken, cut, or burnt out.
Does the voltage consumed by bells deternine entirely the voltage required from the transformer?
Yes, completely. Kirchoff's voltage law states that the sum of the signed voltage drops going around a series circuit add up to zero. The voltage produced by the transformer is completely consumed by the bell when the button is pressed completing a series circuit.
Why an ideal voltage regulation of a device has zero value?
An ideal regulator would hold the thing it is regulating (e.g. voltage, current, water pressure, motor speed) absolutely constant, or in other words with zero variation of that parameter. The quality of regulation in actual regulators however can only approach this ideal of zero variation.
How do you determine angle between primary line voltage and secondary line voltage of a 3-phase transformer?
You should look at the transformer vector diagram, or the type of transformer will tell you (something like YnD1, for example). If it's a Y/Y type transformer, the phase angle will be zero. If it is a D/D, it will be zero. If it's a Y/D, or D/Y, it could be +30, -30 (usually). I have seen a few strange cases where a Y/D was +150 degrees.
What is zero current transformer?
It is a transformer with No load attach to it.
What is meant by transformer charging?
Most likely this is referring to the initial inrush that occurs when a transformer is energized. The core of a transformer is designed for a specific magnetic field strength; When a transformer is switched into a circuit, it usually will not be switched at exactly a voltage peak. When the voltage is at its' peak, the induced magnetic field will be at zero. If the switching occurs at a voltage zero, the magnetic field strength will attempt to climb to double the designed value; since the transformer core is not generally oversized to this degree, it will saturate. This causes large inflows of current to the transformer, and shows up as even harmonics (mainly second harmonics) in the current waveform. This settles out within a few seconds (generally) to a small energizing current, usually less than 1% of the transformer's rated current.
Why are transformers helpful when using alternating current?
The transformer in the least complex manner can be depicted as a thing that means up or ventures down voltage. It is fundamentally a voltage control gadget that is utilized broadly in the conveyance and transmission of rotating flow power. Trutech Products is a leading Transformer Manufacturers In Pune
Why LV side is shorted in short circuit test?
Transformer short circuit tests are used to determine the impedances (positive and zero sequence) of the transformer. A simple explanation: to do this one winding is shorted, and voltage is applied to another winding to circulate the normal full load current of the transformer. The impedance of the transformer is the applied voltage divided by the induced current. If one winding was not shorted, the voltage divided by induced current would not give the impedance of the transformer - the induced current would be much lower, giving a much higher impedance measurement that would be essentially meaningless.
