0
What else can I help you with?
Why drain is called common in common drain amplifier?
The term "common" in a common drain amplifier refers to the configuration where the drain terminal of the transistor (typically a MOSFET) is connected to a common reference point, usually ground. In this configuration, the input signal is applied to the gate, and the output is taken from the source, making the drain the terminal that is common to both the input and output. This setup allows for a high input impedance and low output impedance, making it useful for various amplification applications.
Why input is voltage and output is current in fet?
The input is a Gate that is essentially infinite impedance, so no current. The output is essentially the resistance between Source and Drain, which controls the current flowing through it.
Is it legal to have your washing machine drain into your sump pump which is connected to the main sewer pipe?
No! Dumping the washer output into the sump is illegal.
What is the output impedance of common source amplifier circuit?
The output impedance of a common source amplifier circuit is typically high. This is because the common source amplifier uses a resistor to provide biasing, which results in a high output impedance. However, this can be mitigated by using a current source instead of a resistor for biasing.
How does a MOSFET control output current?
A MOSFET (Metal-Oxide-Semiconductor Field-Effect Transistor) controls output current by using an electric field to regulate the flow of charge carriers (electrons or holes) between its source and drain terminals. When a voltage is applied to the gate terminal, it creates an electric field that alters the conductivity of the channel between the source and drain, allowing or blocking the flow of current. The amount of current that flows is proportional to the gate voltage, enabling precise control over the output current in various applications like switching and amplification.
Why drain is called common in common drain amplifier?
The term "common" in a common drain amplifier refers to the configuration where the drain terminal of the transistor (typically a MOSFET) is connected to a common reference point, usually ground. In this configuration, the input signal is applied to the gate, and the output is taken from the source, making the drain the terminal that is common to both the input and output. This setup allows for a high input impedance and low output impedance, making it useful for various amplification applications.
How do you calculate the Volumetric efficiency of a hydraulic motor?
Dear friend, Drive the motor through a pump. Supply oil to achieve a given rpm and pressure. Some oil will come out of case drain port and some from the out put port of the motor. Measure the out put flow of the motor and input flow to the motor. out put by input will be the volumetric efficiency ( the loss is case drain ) ( alternatively, case drain and output flow fof the motor can be measured, then output flow divided by the sum of output flow and case drain flow is the efficiency ) Rajeev T G tgr-bw@bw.ltindia.com
Why input is voltage and output is current in fet?
The input is a Gate that is essentially infinite impedance, so no current. The output is essentially the resistance between Source and Drain, which controls the current flowing through it.
What is transmission Gate circuit?
It has 3 inputs. They are source, n gate, p gate and only one output that is drain
Is it legal to have your washing machine drain into your sump pump which is connected to the main sewer pipe?
No! Dumping the washer output into the sump is illegal.
How do you use signal generator to test transistor?
To test a transistor using a signal generator, first configure the signal generator to output a small AC signal at a specified frequency, typically in the audio range. Connect the generator's output to the base (for BJT) or gate (for FET) of the transistor while grounding the emitter/source and collector/drain appropriately. Measure the output at the collector/drain with an oscilloscope to observe the transistor's amplification characteristics. By analyzing the output waveform and its relation to the input signal, you can assess the transistor's performance and functionality.
What is the voltage gain of the FET amplifier?
It can be answered in two ways : 1. ratio of output & input voltages [Vout / Vin] i.e Drain voltage(Vds)/Source voltage(Vs). 2. multiplication of trans-conductance & drain resistance .
What attention should be given to surgical drains after a mastectomy?
The surgical drains must be attended to properly; this includes emptying the drain, measuring fluid output, moving clots through the drain, and identifying problems that need attention from the doctor or nurse.
What is the output impedance of common source amplifier circuit?
The output impedance of a common source amplifier circuit is typically high. This is because the common source amplifier uses a resistor to provide biasing, which results in a high output impedance. However, this can be mitigated by using a current source instead of a resistor for biasing.
Your volt meter reads 16 volts at the battery at idle The alternator and voltage regulator have been replaced Do you have a problem?
Alternator Output Voltage RangeGenerally, alternator output voltage is consider OK if it is in the range between 12 1/2 volts to a maximum of 16 volts.Therefore, although the output is at the maximum, you do not seem to have a problem.Usually, if the battery has had a lot of drain, then the alternator output will run at the maximum until the battery is fully charged.
How can you implement c-bicmos using nand gate?
draw its cmos equivalent and give its output to pull up bjt.then draw nmos block of the logic and connect its drain to
How does a MOSFET control output current?
A MOSFET (Metal-Oxide-Semiconductor Field-Effect Transistor) controls output current by using an electric field to regulate the flow of charge carriers (electrons or holes) between its source and drain terminals. When a voltage is applied to the gate terminal, it creates an electric field that alters the conductivity of the channel between the source and drain, allowing or blocking the flow of current. The amount of current that flows is proportional to the gate voltage, enabling precise control over the output current in various applications like switching and amplification.
