0
In general, a longer winding has more resistance than a shorter winding, assuming the same material and cross-sectional area are used. This is because resistance is directly proportional to the length of the conductor and inversely proportional to its cross-sectional area, according to the formula ( R = \frac{\rho L}{A} ), where ( R ) is resistance, ( \rho ) is resistivity, ( L ) is length, and ( A ) is the cross-sectional area. Therefore, if comparing two windings of the same material and thickness, the longer winding will inherently have higher resistance.
What else can I help you with?
Why armature winding resistance is less than field winding resistance?
An 'armature winding' is the rotor winding, and the 'field winding' is the stator winding.
Does a starting winding has more or less turns than a running winding?
Starting winding has more resistance and less induction than main winding, this means has smaller diameter and less turns.
Which winding has the higher resistance start or run in single phase motors?
start winding is thicker with less number of winding whereas run winding is less thicker than start winding but with more number of winding. As we know inductance depends upon numbers of turns of winding so run winding will have more inductance.
Does a step-up transformer have a higher primary or secondary resistance?
It is a step up transformer since the secondary windings are greater than the primary. the turns ratio is (primary to secondary) 1:5, so the primary voltages is 1/5 of the secondary (5 volts).
If the series field winding of your motor was connected directly across the 120 V dc supply a. What current would flow?
If the series field winding of a motor is connected directly across a 120 V DC supply, the current that flows through the winding would depend on the resistance of the winding itself, as per Ohm's Law (I = V/R). If the resistance of the winding is known, you can calculate the current by dividing the voltage (120 V) by the resistance (R). Without knowing the specific resistance value, the exact current cannot be determined.
Does series field winding have more resistance or a shunt field winding?
shunt field winding have more resistance than series field winding ************sai ganesh ************269*******
Why armature winding resistance is less than field winding resistance?
An 'armature winding' is the rotor winding, and the 'field winding' is the stator winding.
How is the resistance of a motor winding expressed?
The resistance of a motor winding is expressed in
Does a starting winding has more or less turns than a running winding?
Starting winding has more resistance and less induction than main winding, this means has smaller diameter and less turns.
Which winding has the higher resistance start or run in single phase motors?
start winding is thicker with less number of winding whereas run winding is less thicker than start winding but with more number of winding. As we know inductance depends upon numbers of turns of winding so run winding will have more inductance.
Is the resistance in the start winding greater or less than the resistance in the run winding?
The resistance in the start winding is greater because it is longer and thinner and has the greatest resistance to current flow
Why is the shunt field resistance greater than the series field resistance?
In case of series winding total line current is flow through it.line current is very very high.so,to minimize the drop the winding made as low turns and low gauge.hence the resistance is low.in case of shunt winding high resistance winding is used otherwise short circuit the parallel winding.for that winding is made as heavy turns and heavy gauge.
How do you measure wiring winding resistance?
Through an omhmeter.
Does a step-up transformer have a higher primary or secondary resistance?
It is a step up transformer since the secondary windings are greater than the primary. the turns ratio is (primary to secondary) 1:5, so the primary voltages is 1/5 of the secondary (5 volts).
What type of test equipment would you use to check the resistance between motor winding?
Ideally megger test is the best test used to check the resistance of motor winding.
If the series field winding of your motor was connected directly across the 120 V dc supply a. What current would flow?
If the series field winding of a motor is connected directly across a 120 V DC supply, the current that flows through the winding would depend on the resistance of the winding itself, as per Ohm's Law (I = V/R). If the resistance of the winding is known, you can calculate the current by dividing the voltage (120 V) by the resistance (R). Without knowing the specific resistance value, the exact current cannot be determined.
The insulation resistance of a transformer winding can be easily measured with?
It depends on the rated voltage of the transformer winding -are you talking about a 12-V transformer winding or a 400-kV transformer winding? Obviously, there is no one answer to your question!
