0
A long handled wrench gives you more leverage on those very tough bolts. However, a long wrench also has difficulty moving in tight quarters, so to counter this I carry a 16" piece of 1 1/2 steel pipe, flattened at one half. This easily slides over even my biggest wrenches giving me a lot more leverage, yet being able to shorten if I wish.
What else can I help you with?
What is a bolt capacity on an impact wrench?
Depends on size of wrench.
Does loosening a bolt with a torque wrench hurt the torque wrench?
yes
6 point box end wrench should be used when a bolt or nut is extremely tight?
That's correct. This particular wrench holds the nut or bolt head better than any other wrench.
What wrench do you use on a 16MM hex bolt?
You use a 16 mm or 5/8 wrench.
How do you tighten the back bolt under your sink that leads to your angle valve?
Are you asking about the supply line where it attaches to the faucet? If so, they make a wrench that has teeth like a pipe wrench and the head swivels for tighten and loosen. $6 or so. Handy to have for tight places. Most hardware or lumber supply should have it.
What does a bolt's wrench diameter mean?
That refers to the size wrench necessary to tighten or loosen the bolt.
How does a harmonic balancer loosen itself on a 97 Jeep Grand Cherokee 4.0 in-line six and which way does the bolt turn to tighten and can you re-tighten it with standard tools?
Under normal circumstances it will not loosen. You use a torque wrench to tighten it to specifications. Specifications are located in the Haynes repair manual available from www.amazon.com. clockwise to tighten counterclockwise to loosen You need a socket that fits tightly on the bolt head and a long-handled torque wrench.
Which best explains what will happen if sharilyn unscrews a bolt with a short handled wrench?
GLIZZY
How do you remove hub nut on 96 Honda civic?
It won't open with the wrench provided ? Then you need a narrow head cold chisel and a short handled sledge hammer, knocing the head of the bolt carefully at an angle will loosen it.
Which wrench will be most effective in turning a nut or the head of a bolt?
A box wrench is always the most effective to loosen tight nuts.
How do you loosen the top bolt on the stater for 1998 rodeo?
To loosen the bolt, use a socket wrench. You might use the frame for leverage, and you may need some starter or grease on the bolt to give you some give.
Do you need to use a torque wrench to loosen retractor seatbelt bolt on vw caravelle?
You don't use a torque wrench to loosen ANYTHING. -It is only for tightening nuts and bolts to the correct torque.
How do you loosen bolt to remove crank pulley?
To loosen a bolt for removing the crank pulley, first ensure the vehicle is in gear or the parking brake is engaged to prevent the crankshaft from rotating. Use a socket wrench with the appropriate size socket, and if necessary, apply penetrating oil to the bolt to help with rust. If the bolt is particularly stubborn, you can tap the wrench with a hammer or use a breaker bar for added leverage. Remember to turn the bolt counterclockwise to loosen it.
How do you use the wrench?
You fit the jaws onto an appropriate nut or bolt and turn it - clockwise to tighten, anti-clockwise to loosen.
How do you loosen the belt tensioner on a 2005 Chevy trailblazer?
On the tensioner arm there is a bolt holding it there. To the right of the bolt will be a square cut into the arm of the tensioner, use a 3/8 inch socket wrench (no attachment, just the wrench itself) and turn to the right this will loosen the belt to remove it.
How do you loosen stuck bolts without power tools?
You can apply a penetrating oil like WD-40 or PB Blaster and let it sit for a few hours to help lubricate and loosen the bolt. Heat the bolt with a propane torch to expand the metal, making it easier to turn. Using a breaker bar or a longer wrench for additional leverage can also help loosen a stuck bolt.
How to remove a bolt effectively and safely?
To remove a bolt effectively and safely, use the correct size wrench or socket to avoid damaging the bolt head. Apply penetrating oil to loosen the bolt if it's stuck. Turn the wrench or socket counterclockwise to loosen the bolt, applying steady pressure to avoid stripping the threads. Use proper safety equipment like gloves and goggles to protect yourself.
