answersLogoWhite

0

Power-factor improvement capacitors are connected in parallel with the load, and are rated in reactive volt amperes. If their reactive volt amperes are identical with the reactive volt amperes of the reactive component of the load, then they act to cancel each other, and bring the phase angle to zero (i.e. the load current becomes in phase with the supply voltage). This reduces the value of the load current without affecting the operation of the load, and allows cables and switchgear with lower current ratings to be used than would otherwise be necessary.

User Avatar

Wiki User

13y ago

What else can I help you with?

Continue Learning about Engineering

What is the difference between pf and uf capacitor?

PF (polyester film) capacitors and UF (film capacitors using an unspecified type of plastic, often polystyrene) differ primarily in their dielectric materials and applications. PF capacitors are typically more affordable and widely used in general-purpose applications due to their stability and reliability. UF capacitors, on the other hand, often provide better performance characteristics, such as lower distortion and higher frequency response, making them suitable for audio and precision circuits. Additionally, PF capacitors generally have a wider voltage rating compared to UF capacitors.


A circuit contains a 10 pF capacitor and a 50 pF capacitor connected in parallel.What is the total capacitance of this circuit?

When capacitors are connected in parallel, the total capacitance in the circuit in which they are connected is the sum of both capacitances. Capacitors in parallel add like resistors in series, while capacitors in series add like resistors in parallel.


How many capacitors are use in a circuit?

Capacitors store charge. There are many applications for their use. There is no set amount of capacitors in a circuit since it is application dependent.


What are values of capacitors?

Capacitors come in many different shapes, sizes & technologies. However, they all use the same unit of value; the farad. Capacitors will be measured in picofarad (pF), nanofarad (nF), microfarad (uF), farad (F), and megafarad (MF). Do note, however, that MF has not been used since the days of mechanical transistors and other less developed electronic components. Capacitors will also have a voltage rating; this is called the Breakdown Voltage, and it is at this voltage that the dielectric will completely breakdown, usually with catastrophic consequences.


What is capacitor rating notation?

Capacitor rating notation typically refers to the way capacitors are labeled to indicate their capacitance value, voltage rating, and tolerance. The most common format includes a three-digit code representing the capacitance in picofarads (pF), followed by a letter indicating tolerance and the voltage rating. For example, a capacitor marked as "104K 50V" indicates a capacitance of 100,000 pF (or 100 nF), a tolerance of ±10%, and a maximum voltage of 50 volts. Additionally, some capacitors may use alphanumeric designations to specify the dielectric material and temperature coefficients.

Related Questions

What is the difference between pf and uf capacitor?

PF (polyester film) capacitors and UF (film capacitors using an unspecified type of plastic, often polystyrene) differ primarily in their dielectric materials and applications. PF capacitors are typically more affordable and widely used in general-purpose applications due to their stability and reliability. UF capacitors, on the other hand, often provide better performance characteristics, such as lower distortion and higher frequency response, making them suitable for audio and precision circuits. Additionally, PF capacitors generally have a wider voltage rating compared to UF capacitors.


A circuit contains a 10 pF capacitor and a 50 pF capacitor connected in parallel.What is the total capacitance of this circuit?

When capacitors are connected in parallel, the total capacitance in the circuit in which they are connected is the sum of both capacitances. Capacitors in parallel add like resistors in series, while capacitors in series add like resistors in parallel.


How many capacitors are use in a circuit?

Capacitors store charge. There are many applications for their use. There is no set amount of capacitors in a circuit since it is application dependent.


Can you use 50volts 3300uf capacitors instead of 25volts 3300uf capacitors?

Yes.


What are values of capacitors?

Capacitors come in many different shapes, sizes & technologies. However, they all use the same unit of value; the farad. Capacitors will be measured in picofarad (pF), nanofarad (nF), microfarad (uF), farad (F), and megafarad (MF). Do note, however, that MF has not been used since the days of mechanical transistors and other less developed electronic components. Capacitors will also have a voltage rating; this is called the Breakdown Voltage, and it is at this voltage that the dielectric will completely breakdown, usually with catastrophic consequences.


What radios have 365 pf tuning capacitors?

AM broadcast - 535~1605 kHz tuning range. The 365 pF cap is most likely in the aerial circuit, as most modern receivers would use a smaller-value section for local oscillator tuning. Alternately, a set may use the *same* value for aerial and local oscillator, with a padding capacitor to reduce the effective max value of the oscillator section.


What the correct spelling pf grand daughter?

Granddaughter is one word, with no hyphen.


What is capacitor rating notation?

Capacitor rating notation typically refers to the way capacitors are labeled to indicate their capacitance value, voltage rating, and tolerance. The most common format includes a three-digit code representing the capacitance in picofarads (pF), followed by a letter indicating tolerance and the voltage rating. For example, a capacitor marked as "104K 50V" indicates a capacitance of 100,000 pF (or 100 nF), a tolerance of ±10%, and a maximum voltage of 50 volts. Additionally, some capacitors may use alphanumeric designations to specify the dielectric material and temperature coefficients.


Is it advisable to correct the power factor to unity?

power factor depends on the load being fed if the load is entirely resistive power factor will be unity ..if the load includes an inductor or capacitpr due to phase displacement between v and i the pf will be lag or lead respectievly


Which type of dielectric is used most often in variable capacitors?

The type of dielectric most often used in variable capacitors is air. Also, trimmer capacitors often use mica.


What is the use of capacitors in fire alarm circuit?

Fire alarm system may be having some electronic devices and cards, in which some capacitors are used. Capacitors are part of any electronic cards.


Are any capacitor in three phase induction motor?

There doesn't have to be but capacitors are sometimes used to correct the power factor.