A plunger on a Massey Ferguson model 3 hay baler may stick due to several factors, including a lack of lubrication, debris or hay buildup in the mechanism, or wear and tear on components like the plunger bearings. Corrosion or rust can also impede movement, especially if the baler has been stored improperly. Regular maintenance, including cleaning and lubrication, is essential to prevent these issues and ensure smooth operation.
Most states require you be 18 to operate a baler. Some states require that you are only 16.
No, they will not fit. Different mounting pads, different length needle arm.
Forming it into bales via a baler, like hay-so it can be easily distributed. They are turned into nice square bundles and stacked like bricks.
A hydrodynamic coupling is used on a tractor to convert the power of the engine for other purposes. It allows you to operate equipment such as a post hole digger, hay baler, or log splitter from a connection on the tractor.
How do adjust the knotters on #12 Massey Fergurson hay baler
They were made by Vermeer.
Because its a closed mouth baler
To determine the year of a Massey Ferguson 124 baler, you can check the serial number, which is typically located on a plate affixed to the frame. The serial number can provide specific information about the production year when cross-referenced with Massey Ferguson's production records. Additionally, consulting the owner's manual or contacting a Massey Ferguson dealer can provide assistance in identifying the year based on the model's features and specifications.
5 foot X 6 foot
from what I could locate I believe your model 124 was manufctured in 1980
To time a Massey Ferguson 126 wire tie baler, first ensure the baler is properly set up and connected to the tractor. Then, disengage the tractor's PTO and manually rotate the baler’s flywheel to access the timing marks on the crankshaft and connecting rod. Align these timing marks according to the manufacturer’s specifications, typically found in the operator’s manual. Finally, reassemble any removed components and test the baler to ensure it operates smoothly and efficiently.
To time a No. 3 Massey Ferguson square baler, first ensure the machine is properly set up and connected to the tractor. Locate the timing marks on the baler's flywheel and the knotter mechanism. Rotate the flywheel until the timing marks align, then adjust the knotter's drive mechanism to ensure it engages at the correct point in the cycle. Finally, check the operation by running the baler and observing the knotting action to confirm proper timing.
The leading three fingers on a Massey Ferguson 503 hay baler typically measure around 20 inches in length. These fingers are designed to effectively gather and feed hay into the baler for optimal baling performance. It's important to consult the specific operator's manual for exact specifications, as measurements can vary slightly based on the model and year.
To set the timing on a Massey Ferguson 124 baler, first, ensure the baler is disengaged and the tractor is off. Locate the timing marks on the main drive sprocket and the knotter drive. Adjust the knotter timing by loosening the set screws and rotating the knotter drive until the marks align correctly, typically at the point where the plunger reaches the end of its stroke. Finally, re-tighten the screws and verify the timing by testing the baler's operation.
To tighten the belts on a Massey Ferguson 450 round baler, first ensure the baler is turned off and safely parked. Locate the tension adjustment bolts, typically found on the idler pulleys or the main frame, and use a wrench to turn them clockwise to increase belt tension. Check the belt alignment and tension by observing the belts while manually rotating the baler, ensuring they sit evenly on the pulleys. Adjust as necessary until the belts are properly tensioned and aligned.
A plunger on a Massey Ferguson model 3 hay baler may stick due to several factors, including a lack of lubrication, debris or hay buildup in the mechanism, or wear and tear on components like the plunger bearings. Corrosion or rust can also impede movement, especially if the baler has been stored improperly. Regular maintenance, including cleaning and lubrication, is essential to prevent these issues and ensure smooth operation.